User manual JBSYSTEMS LIGHT DMX 512 SUPER Z

[. . . ] The unit must be installed in a location with adequate ventilation, at least 100 cm from adjacent surfaces. Make sure there is no flammable materials close to the unit while operating as it is fire hazard. Don't handle the unit by taking its head only, but always by taking its base. Don't touch the housing bare-hand during its operation, and allow about 15 minutes to cool down before replacing bulb or serving, as the unit could be very hot. [. . . ] Please use 4mm allen wrench to loose the screw of the arm before you adjust the head angle. 2. Technical Specification Power supply - AC 120V ~ 60Hz / 230v ~ 50Hz Lamp - MSD 250W (AK-250) / CDM-T150W (AK-150) Optical system - Standard 45°(AK-250) /30°(AK-150) frost beam angle. DMX architectural color changers ideal for the illumination of buildings, shopping centers, outdoor advertisements, exhibitions, etc. - Good protection, IP55, against liquid and dust, enables the fixtures to function well in unfavorable weather conditions. - Features 2 dichroic color wheels providing blackout and 16 different colors. - Synchronous color changing in Master/Slave linkage with adjustable changing speed. Dimension: 380mm x 240mm x 460mm / 15in x 9. 5in x 18. 2in(AK-250) 333mm x 200mm x 330mm / 13. 2in x 7. 9in x13 in(AK-150) Weight: 25 kg / 55 lbs(AK-250) / 9. 6 kg / 21. 3 lbs(AK-150) Beam angle: 4D 6. Troubleshooting Following are a few common problems that may occur during operation. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one. Check in the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit. The stepper motor might be damaged or the cable connected to the PCB is broken. You will know which unit is the master because its DMX input jack will have nothing plugged into it. The other units (slaves) will have DMX cables plugged into the DMX input jacks (daisy chain). 4. How To Set The Unit 4. 1 Control Panel 5. 2 By Akicolor Processor (AK-1) controller If you use a AK-1 controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal . Hold down the BLACKOUT button, and select the number button to set lighting amount in the chain; when you set the fixtures amount, the DMX address of each light will be set automatically. DMX input/output To select the programming functions To set DMX address value down To set DMX address value up To confirm the selected functions AK-1 function instructions: 7D For DMX512 link, use 3-pin XLR plug cable to link the unit together. 4. 2 Main Function To select any of the given functions, press the MENU button up to when the required one is showing on the display. Adjust chase speed from fast to slow or select colors within the value range 0-255. The buttons for selecting color on White / Red / Orange / Yellow / Amber / Green / Cyan / Blue / Purple / Pink or selecting chase patterns 1~10. 3. Color / number buttons DMX512 Address Setting Press the MENU button up to when the is showing on the display. Use "-" and "+" button to change the DMX512 address. Once the address has been selected, press the ENTER button to setup the DMX address. To go back to the functions without any change press the MENU button again. Focus Adjust Press the MENU button up to when the is blinking on the display. Pressing ENTER button, the unit will focus on different color each time you press ENTER button. Self-Test Show Mode Press the MENU button up to when the is showing on the display. [. . . ] Pressing ENTER button and the unit will run self-test by built in program. Fixture Hours Press the MENU button up to when the functions press the MENU button again. Reset 8D Press the MENU button up to when the functions press the MENU button again. Pressing ENTER button and all channels of the unit will return to their standard position. [. . . ]