User manual JBSYSTEMS LIGHT DB-150 V 1.0

[. . . ] If a foreign object enters the unit, immediately disconnect the mains power. No naked flame sources, such as lighted candles, should be placed on the appliance. Always unplug the unit when it is not used for a longer time or before you start servicing. The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. [. . . ] Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!Don't cover any ventilation openings as this may result in overheating. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. SAFETY EYE: used to attach an optional safety cable when the DB-150 is fixed under ALU-truss (using clamps, also see n°8) Further shows the information related to the selected function or working mode. The left digit shows the channel number, the 3 other digits show the channel status: In the ADDRess menu: channel + DMX address is shown, ranging from 001 to 512 In the MODE menu: working mode is shown. ("DIM" = dimmer mode * "SW" = switch mode) In the ALONE menu and standard display: channel output status is shown. Channel in dimmer mode: dimmer percentage, ranging from 0% to 100% Channel in switch mode: "ON" = output 100% * "OFF" = output 0% Curve : shows the dimming curve that is used 13. MENU BUTTON: Please refer to the menu structure to understand the different menus. These are the different possibilities: Browse the main menu: Press the MENU button together with the UP/DOWN buttons. Return to the main menu: Press the MENU button to return to the main menu. DOWN BUTTON: Please refer to the menu structure to understand the different menus. These are the different possibilities: Browse the main menu: Press the MENU button together with the UP/DOWN buttons. In the ADDRess menu: Press the DOWN button to lower the DMX address of the selected channel. (press the button for a longer time to increase the speed) In the MODE menu: Press the DOWN button to put the selected channel in switch or dimmer mode. In the ALONE menu: Press the DOWN button to lower the dimmer value (0~100%) when the selected channel is in dimmer mode. [. . . ] END CAP: To install the bolts/nuts (needed to fix the projectors) and stand adapter you have to remove this end cap on one side of the unit: simply unscrew the 4 screws remove the cap put the nuts/bolts and/or stand adapter in the sliding rail put the cap back in place fix the 4 screws done!CURVE SUBMENU: This menu is used to choose one of the 3 preprogrammed dimming curves. Please check the diagram with the dimming curves to see which curve suits most for your needs. Power Input: Power outputs: Channel Fuses: Input fuse: DMX input: DMX output: Size: Weight: 230Vac / 20A maximum (4600Watts) 4x 230Vac / 2000Watts 250V/8A (size 20x5mm) 20A "auto reset" thermal circuit breaker 3pin XLR male 3pin XLR female 150 x 9 x 7 cm 5, 0 kg ADDRESS SUBMENU: This menu is used to set the DMX address of the 4 output channels. [. . . ]