User manual JBSYSTEMS LIGHT CMX-24 V 1.1

[. . . ] Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited. Dispose of the unit and used batteries in an environment friendly manner according to your country regulations. To take full advantage of all possibilities, please read these operating instructions very carefully. This product meets the requirements of the current European and national guidelines. [. . . ] All connected light effects will be put out because of the black out function. Fade time: With the FADE fader, you can set the transition time between 0 (INSTANT) seconds and 10 minutes. This function is very handy to make flexible transitions between different scenes. you can set the fade time as long as the transition is in progress (you accelerate or delay the transition) Move the {MASTER A} fader to the lowest position. Move {PRESET A 1} fader to the lowest position Move the {FADE} fader until the display shows [1. The green led (and your connected light effect) will be lit immediately. The table below gives you all the information to set your fade time (x is a digit between 0 and 9) Display Time 0. Channel 1 at 100% Channel 2 at 50% (A:50% is higher then B:25%) Channel 3 at 75% (B:75% is higher then A:25%) This only works when BOTH masters are set at 100%. CHASE/SCENES mode This control mode allows you to store a scène or a chase of 24 channels in every Preset B fader. the CMX24 has 4 pages , so you can store altogether 48 scenes/chases. You can activate this mode like this: Press and release the <MODUS SELECT/REC SPEED> button until the [CHASE SCENES] lamp is lit above the master A/B faders. Using the HOLD button you can maintain the current scene while setting the next scene. The scène will change slowly (within 10 seconds) from the previous to the next. DOUBLE PRESET MODE: In this mode you can use the control as an 12 channel A-B control. Change the mode to double preset: Press and release <MODUS SELECT/REC SPEED> until the [DOUBLE PRESET] lamp will be lit above the master A and master B faders. a chase contains multiple scenes and each scene contains the intensity for 24 channels. The scenes will be showed one by one (and you can set the speed/fade time). You have 4 pages with each 12 PRESET B faders which each can contain a scene or a chase. The CMX24 can work in 3 modes: o Safe mode, in this mode you can't change the programs o Program mode, in this mode you can save/erase programs o Edit mode, in this mode you can change programs Safe mode and program mode are always available, whether you are working in Single Preset, Double Preset or Chase/Scenes mode. Activate the program mode Press and hold the <RECORD/SHIFT> button Press and release the <PRESET A 1> button Press and release the <PRESET A 5> button Press and release the <PRESET A 6> button Press and release the <PRESET A 8> button Release the <RECORD/SHIFT> button The next procedure will delete the complete memory. Delete the complete memory: Press and hold the <RECORD/SHIFT> button Press and release the <PRESET A 1> button Press and release the <PRESET A 3> button Press and release the <PRESET A 2> button Press and release the <PRESET A 3> button Release the <RECORD/SHIFT> button Record a Scene (ONLY possible in program mode. ) Be sure that the work memory is empty: Press and hold the <RECORD/SHIFT> button Press and release the <PAGINA/REC CLEAR> button Release the <RECORD/SHIFT> button Make your settings: If you want to set only 12 channels, u can use the Preset A faders. [. . . ] Preset A To disconnect the channels 1 to 12 from the preset B scenes/chases: o Press and hold the <BLIND> button o Press and release the <Preset A x> button o Release the <BLIND> button The level will only be determinated by using the preset A fader, master A fader and the flash buttons. Move all the Preset A faders to their lowest position Choose the desired page by using the <PAGINA/REC CLEAR> button The easiest way to test this is to activate a chase (by using a preset B fader), then place one of the cannels in BLIND. To place the channel back in normal mode: o Press and hold the <HOME> button o Press and release the <Preset A x> button o Release the <HOME> button Preset B To disconnect the channels 13 to 24 from the preset B scenes/chases: o Press and hold the <BLIND> button o Press and release the <Preset B x> button o Release the <BLIND> button The level will only be determinated by using the preset B fader, master A fader and the flash buttons. The preset B fader will not be linked anymore to its stored scene/chases. [. . . ]