User manual JBSYSTEMS LIGHT BTX 300 SW V 1.0

[. . . ] n'exposez jamais la lentille directement aux rayons de soleil, même pendant un bref instant. Ceci peut endommager l'intérieur de l'appareil ou même causer un incendie !stel de lens nooit bloot aan direct zonlicht, zelfs gedurende een korte periode. Setzen sie die Linse niemals direkter Sonneneinstrahlung aus, auch nicht für eine kurze Zeit ! [. . . ] WDMX Setting--wireless control setting (For the unit with wireless receiver built-in only) Select WDMX Setting, press ENTER button to confirm. Use UP and DOWN button to select Active, Retransmit or Reset Memory, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. BRITEQ® 11 BTX-300SW Lamp Setting Attention: The lamp will not be on unit detected temperature is lower than 45°C. Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and DOWN button to select On/Off, State/Power on, Off Via Dmx, On if Dmx on, Off if Dmx off, Cooling Mode, Ignition Delay or Low Power Delay. . On/Off--Turn on/off the lamp Select On/Off, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select On (lamp on) or Off (lamp off), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. State/Power On--Lamp state while power on Select State/Power On, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select On (Lamp on while power on) or Off (Lamp off while power on), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Off Via DMX--Turn off the unit via DMX controller Select Off Via DMX, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (turn off the unit via DMX controller available) or No (turn off the unit via Dmx controller impracticable), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. (When you operate the unit via DMX controller, set the value of channel "special function" to "lamp off", waiting for 5 seconds, then the lamp will be off if you choose "yes" mode). On If DMX On--Lamp turns on when DMX signal is detected Select On If Dmx On, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (Lamp turns on when DMX signal is detected) or No (keep the present state), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. (If the lamp is off via DMX signal, you can reconnect the DMX controller to make the lamp on). Off If DMX Off--l Lamp turns off when DMX signal is cut off Select Off If Dmx Off, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (Lamp turns off when DMX signal is cut off), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Cooling Mode--Lamp turns off when DMX signal is cut off Select Cooling Mode, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Auto (fans speed adjust automatically) or High (fans run in high speed), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. BRITEQ® 13 BTX-300SW Ignition Delay--Delay time between power on and lamp on Select Ignition Delay, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to adjust the delay time from 0S to 255S, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Low Power Delay--Delay time between reduce lamp power and shutter off the unit Select Low Power Delay, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to adjust the delay time from 0S to 255S, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. (If you set the low power delay time to 3S, the lamp will run in half power 3 seconds after the unit shutters off) Display Setting Enter menu mode, select Display Setting, press ENTER button to confirm, use UP and DOWN button to select Display Inverse, Backlight Auto Off, Backlight Intensity or Temperature unit. Display Inverse Select Display Inverse, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal display) or Yes (inverse display), press ENTER button to store. [. . . ] 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin4, Pin5 not used. BRITEQ® 19 BTX-300SW BRITEQ® 20 BTX-300SW 7. 2 Channel Mode Setting Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Channel Mode, press ENTER button to confirm, present channel mode will blinking on the display, use UP and DOWN button to select Mode1 (22 channels mode) or Mode 2 (22 channels mode) or Mode 3 (29 channels mode), press ENTER button to store. Press MENU button back to the last menu or idling let the unit idle one minute to exit menu mode. 7. 3 Address Setting If you use a universal DMX controller to control the units, you have to set DMX address from 1 to 512 so that the units can receive DMX signal. Press MENU button to enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Address, press ENTER button to confirm, the present address will blink on the display, use UP and DOWN button to adjust the address from 0 to 512, press ENTER button to store. [. . . ]