User manual JAWBONE JAWBONE

[. . . ] Jawbone automatically enhances incoming audio: The volume and frequency content of the incoming speech is dynamically adjusted to maximize intelligibility in any noise environment. No matter where you are, Jawbone will adapt to your environment. 1 Jawbone Package Contents What's in the boxes? Getting Started 1. Connect Jawbone to the USB cable with the lettering "TOP" facing up. The crescent hole of the connector should be facing down so that it engages with Jawbone's earplug. Box 1: Customize your fit · 1 Standard Right Ear Earloop ("Standard R ") · 1 Standard Left Ear Earloop ("Standard L") · 1 Large Right Ear Earloop ("Long R ") · 1 Large Left Ear Earloop ("Long L") · 4 Earbuds of various sizes and shapes to fit your ear Note: You will find these earloop names are inscribed on the edge of each earloop tail. Box 2: Power up · Wall charger unit with USB socket · USB charger cable 2 3 Once Jawbone has been engaged in the charger cable you can charge Jawbone in two ways: 1. [. . . ] Just select "Jawbone" from the list of paired devices and connect to it. IMPORTANT: If the pairing cannot be completed within two minutes after the pairing mode has been activated, Jawbone's LED indicator will flash red and beep three times. Please repeat steps 2 to 8 above to pair Jawbone and the mobile phone again. `TALK BUTTON' once when Jawbone is in standby. Jawbone automatically enhances the volume of your call depending on the noise of your environment. If you want to adjust the volume of your call further, use your mobile phone's volume button or press the `NOISE SHIELD BUTTON' one time to increase the volume by one level (there are a total of six levels). 4. Turning Jawbone On and Off Press and hold the `TALK BUTTON' for three seconds until you hear a short beep. The LED status indicator will then flash white. IMPORTANT: After you turn Jawbone on, you may need to press the `TALK BUTTON' one time to reactivate pairing and resume the connection between the headset and the mobile phone. (For pairing instructions, please refer to the "Pairing Jawbone" section. ) Using Jawbone after it is Paired and Connected 1. If Jawbone is connected to the phone and you make a call, the audio will automatically be routed to Jawbone. To make a call using voice dialing, press the 10 Turning off Jawbone To turn Jawbone off, press and hold the `TALK BUTTON' for three seconds until you hear a long beep. The LED status indicator will flash red and then go off. 11 Using Jawbone Talk Button Answering a Call When there is an incoming call, you will hear the ring through the earphone. Press the `TALK BUTTON' once to accept the call or answer the call using your mobile phone by following the phone's normal procedure. Ending a Call Press the `TALK BUTTON' once to end your call, or end the call using your mobile phone by following the phone's normal procedure. Noise Shield Button Turning Jawbone Noise Shield Off While on a call, press and hold the `NOISE SHIELD BUTTON' for 3 seconds. The LED status indicator will blink red and descending tones will be heard in the earpiece. Rejecting a Call If you do not wish to answer an incoming call, press the `NOISE SHIELD BUTTON' button once to reject the call. Dialing from Your Mobile Phone Simply make calls on your mobile phone by following the phone's normal procedure. Turning Jawbone Noise Shield On While on a call, press the `NOISE SHIELD BUTTON' for 3 seconds. The LED status indicator will blink white and ascending notes will be heard in the earpiece. Note: The Noise Shield technology is on by default whenever Jawbone is turned on or a call is received or placed. Voice Dialing from Jawbone If your mobile phone is equipped with a standard voice dialing function, simply press the `TALK BUTTON' once when in Standby Mode, and when you hear a beep say the voice tag. We recommend that you record the voice tag using Jawbone for maximum effectiveness. 13 12 Last Number Redialing from Jawbone Depending on your phone's functionality, you may be able to redial your last placed call by pressing the `TALK BUTTON' on your headset twice while in standby mode. Transferring a Call from Jawbone to Mobile Phone Handset While on a call, press and hold the `TALK BUTTON' for 3 seconds 2. Press the `NOISE SHIELD BUTTON' one time to increase the volume by one level. By pressing the `NOISE SHIELD BUTTON' again, you will advance through these volume levels and hear a 2-step tone. Each successive volume level is identified by a corresponding pitch increase in the second tone. After reaching the maximum volume, you will hear two tones of the same pitch. Once you reach the maximum volume level, if you press the `NOISE SHIELD BUTTON' again, Jawbone will return to the lowest volume level. NOTE: Not all phones support the first option. IMPORTANT: The above functions are only applicable to mobile phones that support the Bluetooth Handsfree Profile. Please refer to your mobile phone user guide for additional information. Transferring a Call from Mobile Phone to Jawbone If you have already transferred a call from Jawbone to your mobile phone, you may reverse the process by pressing the `TALK BUTTON' one time. Adjusting the Volume Jawbone will adjust the volume accordingly depending on your noise environment. [. . . ] Other chargers may look the similar but using them could be dangerous and could damage Jawbone. · Do not attempt to disassemble the charger as it may expose you to dangerous electric shock. · Only charge your Jawbone's built-in battery in accordance with the instructions described in this user guide. · Avoid charging your Jawbone in extremely high or low temperatures. [. . . ]