User manual JANE SONIC EVO

[. . . ] INSTALLING THE FRONT WHEELS: press the lever of the two front wheels (fig_a), insert the wheel until it clicks into place (fig_b) and check that it is securely attached (fig_c). INSTALLING THE REAR WHEELS: carefully distinguish between the two rear wheels connected by the brake cable: the rear left wheel features a slot that matches a corresponding rib on the rear left chassis tube. Press in the wheels until they click into place (fig_a) and check that they are firmly attached (fig_b). ATTACHING THE BASKET: insert the loops over the front hooks (fig_a) and rear hooks (fig_b) and button down the two flaps around the front tube (fig_c). [. . . ] ATTACHING THE CUP HOLDER: insert the cup holder on the corresponding peg and press down until it clicks into place (fig_a). EXTENDABLE HANDLES: to extend the handles press the top of the button and pull upwards the same time (fig_a); to retract the handles press the bottom of the button and push the handle downwards at the same time (fig_b). FIXED OR SWIVELLING FRONT WHEELS: lift the levers to prevent the front wheels from swivelling (fig_a), lower the levers to allow the front wheels to swivel (fig_b). rEAR WHEELS WITH CENTRAL BRAKE CABLE: press a brake lever to set the brake (fig_a) , lift the lever to release it (fig_b). MOUNTING THE SEAT TO THE CHASSIS: the reversible seat can be attached to the chassis either facing the person pushing the stroller (fig_a), or facing forwards (fig_b), place the seat on the chassis so that it is aligned with the relative symbols and press downwards with both hands until you hear two clicks confirming that it has locked into position. Ensure the seat is correctly secured by attempting to pull it upwards by gripping the front bar. REMOVING THE SEAT FROM THE CHASSIS: move the two levers in the direction of the arrow (fig_a) and squeeze the two handles up (fig_b) to release. The seat can be removed from and re-attached to the chassis when it is occupied by a child. FRONT BAR: to attach the front bar, slide the connections into the end of the armrests, press the two side buttons and push the bar towards the seat until it clicks into place (fig_a). To fold the stroller set the front wheels to their fixed position and close the hood. Lift the two levers of the handles together and push directly toward the ground to release the side tubes (fig_a-b), pull the central handle upwards (fig_c) until the safety catches engage (fig_d). TRANSPORT: the stroller can be carried by the central handle, keeping the front wheels fixed (fig_a) or by the side handle (fig_b). REMOVING THE INTERNAL LINING: remove the leg divider strap (fig_a) from the top (by pushing it up from under the seat), detach the two elastic loops of the sack from the footrest and undo the four buttons on the seat (fig_b); Use a screwdriver to remove the hood fastener, then remove the hood (fig_c), undo the two snaps at the sides of the backrest and slip off the lining (fig_d), unscrewing the safety belts from both sides (fig_e). REMOVING THE OUTER LINING: first remove the internal lining, then with the backrest in its raised position detach the two elastic loops on the inside (fig_a), detach the two covers (fig_b), extract the four tabs (fig_c), slip the outer lining off the hood tabs (fig_d) and unscrew the handle from both sides to complete the operation (fig_e). 25 Ganciomatic is a fast and practical system that allows you to attach the Primo Viaggio car seat or the Pliko Switch seat to the Ganciomatic Base of the chassis in one quick step. Place the item on the Ganciomatic Base and press down with both hands until it clicks into place. Always apply the chassis or stroller brake before attaching and removing products (refer to the respective instruction manuals). PRODUCT MAINTENANCE: protect from the weather: water, rain, or snow; prolonged and continuous exposure to bright sunlight may give rise to colour changes of various different materials; store this product in a dry place. [. . . ] Always apply the chassis or stroller brake before attaching and removing products (refer to the respective instruction manuals). PRODUCT MAINTENANCE: protect from the weather: water, rain, or snow; prolonged and continuous exposure to bright sunlight may give rise to colour changes of various different materials; store this product in a dry place. CLEANING THE CHASSIS: periodically clean all plastic parts with a damp cloth. Do not use solvent or similar cleaning products; keep all metal parts dry to prevent rusting; keep moving parts clean (adjustment mechanisms, locking mechanisms, wheels, . [. . . ]