User manual JACUZZI PORTE COULISSANTE MAESTRIA 1

[. . . ] This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with the instructions, it may cause harmful interference to radio. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Regardless of the cleanser used, use extreme care to assure that no soap residue is left on the surface. Headrest Care - Clean the headrests in your spa as needed by wiping them with a clean cloth or soft brush saturated with detergent soap. - In order to remove the headrest should the spa remain unused for a period of time or to replace the headrest, take hold of the ends of each headrest and carefully pull towards yourself. - To reinstall, over mounting strip and press down until headrest mounting bracket emits a "click" sound. Maintaining the Cover Install the isolating cover each time the spa remains unused so that the water heating and spa maintenance times are reduced. To increase the duration of the cover, treat with care and clean regularly with neutral soap and water; a periodic application of specific products available through authorised resellers ensures protection against UV rays. N. B. : Never allow anyone to stand or sit on the cover. 2. 3. 4. 5. 2. Locate the drain valve on the front/lower panel. Hold the larger (rear) body to prevent it from turning, then loosen and remove the cap. Attach the hose. 57 Panel maintenance The panels do not require any special maintenance. To clean them, just wipe them with a clean cloth soaked in a soultion of water and a neutral detergent. ATTENTION: do not direct jets of water against against the, since electro-mechanical parts of the spa are located behind them. - Replace the drain plugs and screw them on. "PUMP DOES NOT OPERATE" Heater is deactivated; recirculation pump may also be deactivate. Proper flow of water is obstructed or a flow switch has malfunctioned. Check for proper water level and for a clogged filter cartridge. I If there is not a noise (relative to the possible functioning of "SHORTED SENSOR" The maximum temperature sensor does not work (the heater is deactivated). I Contact your reseller or an authorised assistance centre. "START-UP MALFUNCTION" CLOSE D OR SHORTE D FLOW SWITCH ON SYSTE M STARTUP (system disabled) Flow switch is non-functional. I Contact your reseller or an authorised assistance centre. Temperature symbol is flashing Indicates that: I There is a difference of approximately 6 °C between the real temperature and the set temperature or I The temperature sensor has read a value exceeding 44 °C, or I The maximum temperature sensor has read a value exceeding the electro-mechanical parts) or if there is a continuous hum, disconnect the spa (the pump could be incorrectly primed; refer to the "The pump does not operate" chapter). I Contact your dealer or service center. 46 °C. "FREEZE PROTECTION" A potential freeze condition has been detected. However, if after 2 hours freezing conditions persist, the pumps will restart automatically. "Please check filter" (check the filter cartridge) 6:45 PM 102F Please check filter! T emp. 59 This message appears when the reminder for the change or cleaning of the filtering cartridges expires. I Clean or replace the filter cartridge (see also relative chapter). Troubleshooting If the spa does not operate correctly review all of the installation and operating instructions in the present manual and control the message shown on the display. Refer, therefore, to the following instructions : NONE OF THE COMPONENTS OPERATE (i. e. pump, light) "Feature not installed" (option not available) EXTERIOR A Feature not installed C Check the control panel lights. D B This message appears when you attempt to activate an option relative to the external lights. I Press the D key to cancel the message from the display. I If there are letters or symbols displayed on the screen, refer to the previous section to determine meaning and action required. THE PUMP IS NOT WORKING EVEN IF THE CORRESPONDING ICON ON THE DISPLAY IS ON "Reset settings?" (zeroing of settings) SETTINGS 2 SETTINGS 2 Primary Secondary Heating Press to reset to default OFF A B Primary Reset Settings?Secondary OFF F Heating to confirm Press Press Press to cancel to reset to default Press the key relative to the control panel. I If no sound is detected or if a buzzing sound is is detected, This message appears when you choose to zero the settings relative to the settings 2 menu in order to reset the default values. I Press the central key on the circular keypad to zero. Press the D key to leave the settings unaltered. turn off power to the spa and contact your dealer or authorized service center. I If motor operates but no water flows to jets: - Pump may not be properly primed. - Contact dealer or authorized service center. "Remote control connection" (remote control connection to system) REMOTE CONTROL CONNECTION REMOTE CONTROL CONNECTION Pump priming instructions: TURN SPA OFF - Turn off the power to the spa. - Remove the knob of the selector of the type of massage which is fed by the pump that you want to prime. [. . . ] . J-1000TM AUDIO SYSTEM STEREO TROUBLESHOOTING Unit will not turn-on Make sure spa power is turned on, then check harness fuse on side of unit making sure they are the proper ratings: · Memory line yellow B+ (10 A fuse). · When faced with a malfunction during operation, push BND button (8) and EJ button (13) at the same time to reset software. Using a thin rod to press the reset button located besides the USB (10) docking station to do a hardware reset. 10dB 25dB 80dB 30dB 35dB CD Player Sampling frequency (8X oversampling) . 20-20 kHz Audio Maximum power (45 watts x 4 channel, 4 ohms, 1kHz) . [. . . ]