User manual JABRA CLIPPER

[. . . ] - The headset will automatically turn off after 10 minutes if not connected to a device . PAIRInG YoUR JABRA CLIPPeR to A PHone oR otHeR DeVICe Headsets are connected to phones or other Bluetooth® devices using a procedure called `pairing' . by following a few simple steps, pairing can be done in a matter of seconds . First time pairing - Turn on the headset and the Jabra CLIPPEr will automatically enter pairing mode (indicator light is solid blue) and start searching for a device . Jabra CLIPPEr 4 english 2. Set your Bluetooth® phone or device to search for the Jabra CLIPPER - Follow your phone's instruction guide . [. . . ] Answer a call when playing music - Tap the Multi-Function button and the music will be paused and the call will be connected . End a call - Tap the Multi-Function button to end an active call ­ when you end the call, your music will start again** . Skip one track forward** - Press and hold the `+' volume control button . Skip one track back** - Press and hold the `­` volume control button . * refer to phone's user manual ** Phone dependent Jabra CLIPPEr 6 english IMPORTANT: DO NOT EXTEND THE METaL-CLIP bY MOrE THaN FOUr (4) MILLIMETErS, aS IT WILL bEND OUT OF SHaPE PErMaNENTLY . Answer a call - Tap the Multi-Function button to answer a call . Reject a call** - Press and hold the Multi-Function button when the phone rings to reject an incoming call . Depending on your phone settings, the person who called you will either be forwarded to voice mail or hear the busy signal . Make a call** - When your Jabra CLIPPEr is connected to your phone, all calls made from your phone will automatically be transferred to your headset (subject to phone settings) . Adjust sound and volume* - Tap the +/- volume control button to turn volume up or down . Mute microphone when on a phone call - Tap the ­ and + volume button simultaneously to mute and un-mute . Adjust sound and volume* - Tap the +/- volume control button to turn volume up or down . HeADset AUDIo AnD VIsUAL InDICAtoRs The Jabra CLIPPEr provides status messages using both lights and audio signals . For example, the LED lights various colors to indicate battery level, incoming calls, on/off operations, etc . audio signals tell you when you have pressed a button or changed the volume; in-ear ring tones are also provided . * refer to phone's user manual ** Phone dependent Jabra CLIPPEr 7 english End a call - Tap the Multi-Function button to end an active call . LED light Solid blue Slow single blue flash Single blue flash Quick blue double flash Solid red Solid green Single red flash In pairing mode ­ see `Pair Jabra CLIPPEr to a phone or other device' Connected to a phone and in standby mode Connected to phone and active on call Incoming call Charging Fully charged Low battery The Jabra CLIPPEr Display LED turns off after 30 seconds of inactivity . The headset is still active, and light will flash again after a tap on the Multi-Function button or any call activity . Communication by Audio Indicators Your Jabra CLIPPEr employs sound alerts to communicate different actions or information . One important alert is the "Low battery" alert, which is two short beeps, and indicates 5 minutes of battery time remains . another sound alert is the "Mobile away" alert, which is four short beeps, and indicates you are moving out of range of your mobile phone . Jabra CLIPPEr 8 english What the LED means: The LED on the front side of Jabra CLIPPEr indicates different states of the product: UsInG YoUR JABRA CLIPPeR WItH tWo MoBILe DeVICes The Jabra CLIPPEr is capable of having two different Bluetooth® devices connected to the headset at the same time ­ e . g . This means that for example, you can use the same headset for both listening to music from your mobile phone as well as answering mobile phone calls and use it for Internet telephony (e . g . Please note: Jabra CLIPPEr does not support two mobile phones at the same time . tRoUBLesHootInG & FAQ What is Bluetooth® Stereo/A2DP?- Bluetooth® Stereo enables a wireless connection of stereo audio between two Bluetooth® Stereo devices . In order to provide a wireless Bluetooth® Stereo connection between two devices, both devices must support the a2DP (advanced audio Distribution Profile) Bluetooth® profile . - audio Video remote Control Profile (aVrCP) enables you to remote control your music player from the Jabra CLIPPEr with functions such as Pause, Play, Stop & Skip Track (can be phone dependent) . [. . . ] This makes your device and the Jabra CLIPPEr recognize each other and automatically work together . 5 Standby mode is when the Jabra CLIPPEr is passively waiting for a call . When you `end' a call on your mobile phone, the headset goes into standby mode . Dispose of the product according to local standards and regulations . www . jabra . com/weee Jabra CLIPPEr 12 english © 2010 GN Netcom US, Inc. [. . . ]