User manual ITI ADVENT COMMERCIAL FIRE SYSTEM REV B

[. . . ] 60-562-03 60-562-06 $GYHQW &RPPHUFLDO )LUH 6\VWHP Document Number: 466-1705 Rev. B November 2001 User's Manual System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Global Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Keep a separate log of all programmed user codes and their user names in a secured location. 3. Enter the area to redi- System displays arming status for rect the touchpad to. that area. Global Status and History If partitions have been turned into areas, the user can also check for global status and history. Selecting global status allows the user to view the following: Whether any alarms are active in any enabled area. Status of main power and main battery. AdventTM Commercial Fire System 3 Access Codes To add an access code: To list access codes: Steps 1. Enter your primary ACCESS CODE. Response SECURITY MENU; ENTER YOUR CODE ACCESS CODE MENU ENTER THE NEW CODE THEN PRESS Steps 1. Press 3. Response SECURITY MENU; ENTER YOUR CODE ACCESS CODE MENU USER 3. Press * twice to exit. # CODE XXXX NO TEXT AUTH:X LIM:X ENTER THE CODE A SECOND TIME THEN PRESS # CODE OK Note No two access codes can be alike. If you are unsuccessful adding an access code, make sure the new access code doesn't already exist in the system. To check the existing codes, from the main menu select 1, 8, your access code, and 3. For LIM you can have the following options: P = Permanent, D = Day, and U = Use. For AUTH, you can have the following options: P = Partition, F = Full, or 1-8. Press * twice to exit. MAIN MENU Changing an Access Code To ensure maximum security, access codes should be changed on a regular (monthly) basis. You should also change an access code if you suspect an unauthorized person knows a user's access code or if/when a user is replaced. To change an access code: Deleting an Access Code Delete an access code when you no longer want that code to allow access to the system. To ensure maximum security, delete access codes as soon as they are no longer needed. To delete an access code: Steps 1. Press * twice to exit. Response SECURITY MENU; ENTER YOUR CODE ACCESS CODE MENU ENTER THE CODE TO DELETE THEN PRESS # CODE DELETED Steps 1. Enter your primary ACCESS CODE. Response SECURITY MENU; ENTER YOUR CODE ACCESS CODE MENU ENTER THE CODE TO CHANGE THEN PRESS # ENTER THE NEW CODE THEN PRESS ENTER THE CODE A SECOND TIME THEN PRESS # CODE OK 3. Enter the new ACCESS CODE again and press # Note If you are unsuccessful deleting an access code, make sure the access code exists in the system. To check the existing codes, from the main menu select 1, 8, your access code, and 3. Also, the system will not let you delete the primary access code. #. 7. If you are unsuccessful changing an access code, make sure the new access code doesn't already exist in the system. To check the existing codes, from the main menu select 1, 8, your access code, and 3. Listing Codes When listing codes, the panel displays the user number, code, user text, limits, and authority level. Note A partition code cannot view global codes. Access Code Options When you add an access code, you can give each access code different options. Permanent User Day Limit Use Limit Authority Levels 4 AdventTM Commercial Fire System Access Codes Permanent User All new access codes are automatically permanent unless you set a Day/Use Limit on it. Select Permanent User when you want to erase the Day Limit or Use Limit of an access code. [. . . ] Enter your primary ACCESS CODE. Response PHONE MENU; ENTER YOUR CODE PHONE TEST ON Cleaning the System Components You should clean your system at least once per year, or as needed. Use a damp, warm rag and a mild, non-abrasive, water-based cleaning solution to clean all touchpads, panels, sensors, and pull stations. 3. report PHONE TEST OK System Status Checking the System Status Check the system status when you want to know the current status of the system and any current problems. To check the system status: Testing Devices A zone test allows you to activate any alarm triggering device and verify its correct operation without causing an alarm. Note All fire protection is disabled during zone test. Steps 1. Press UNDO (*) to quit. Response SECURITY MENU; SYSTEM STATUS . . . . . . . . . [. . . ]