User manual ISEKI KC 350

[. . . ] As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc. ). It is advisable to keep only the cylinder being used in the room, positioned so that it is not subject to heat produced by external sources (ovens, fireplaces, stoves, etc. Fitting the appliance Gas and mixed hobs are manufactured with type X degree protection against overheating. The following precautions must be taken when installing the hob: • Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm from the edge of the hob. [. . . ] Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. The internal burner has a nozzle, the external burner has two (of the same size). Replace the nozzle with models suited to the new type of gas (see table 1). replace all the components by repeating the steps in reverse order. • Setting the burners to minimum: 1. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. GB 3. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance.  If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible.  Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used.  Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). DATA PLATE Electrical connections • Adjusting the burners’ primary air : Does not require adjusting. voltage of 220-240V ~ 50/60Hz voltage of 220-230V ~ 50/60Hz maximum power absorbed 2000W (see data plate ) This appliance conforms to the following European Economic Community directives: -73/23/EEC dated 19/02/73 (Low Voltage) and subsequent amendments - 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. Since the burner is equipped with a safety device, after lighting the burner keep the knob pressed in for about 2-3 seconds to allow the device which keeps the flame lit automatically to heat up. The selected burner can be regulated using the corresponding knob, as follows: • Off Maximum Minimum To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “•” position). Ceramic Glass Module* This cooktop is fitted with dual-ring radiant heating elements located beneath the glass. It is possible to turn on only the circular part of the elemement (identified by the letter "A") or the cooking surface can be enlarged by turning on both "A" and "B". To turn only the circular "A" element, simply turn the knob in the clockwise direction to any one of the 12 available settings. Then setting 12 and then click it into the proceed by turning the knob in the counter-clockwise direction to one of the 12 settings. The figure shows the heating zones, which become red when the element is turned on. Indicator light to show when the cooking zone is above A 60°C, even after the heating element has been turned off. C When the knob is on any of the settings other than "Off", the Indicator Light for Ceramic Glass Module comes on. Practical advice on using the burners To ensure the burners operate efficiently: • Use appropriate cookware for each burner (see table) so that the flames do not extend beyond the bottom of the cookware. * Only available on certain models. 20 • Always use cookware with a flat base and a cover. • When the contents of the pan reach boiling point, turn the knob to minimum. Burner Semi-Rapid (S) Auxilliary (A) Double flame (DCDR internal) Double flame (DCDR external) ø Cookware diameter (cm) 16 - 20 10 - 14 10 -14 26 - 28 • Always use pans with a diameter that is large enough to cover the hotplate fully, in order to use all the available heat. GB • Make sure that the bottom of the cookware is always dry and clean to guarantee correct adherence and long life, not only for the cooking zones but also for the cookware itself. • Avoid using the same cookware that is used on gas burners: the heat concentration on gas burners may deform the base of the pan, causing it not to adhere correctly. [. . . ] Consumers may take their old appliance to public waste collection areas, other communal collection areas, or if national legislation allows return it to a retailer when purchasing a similar new product. All major household appliance manufacturers are active in the creation of systems to manage the collection and disposal of old appliances. 22 Maintenance and care Switching the appliance off Disconnect your appliance from the electricity supply before carrying out any work on it. items, objects made of synthetic material, sugar or foods with a high sugar content that have melted onto the surface must be removed immediatley with a scraper while the cooking surface is still hot. Special cleaning products for ceramic glass surfaces form a transparent protective layer which fights diry buildup. [. . . ]