User manual ISEKI BOLENS TX1504

[. . . ] Just touch the key, and the indicator light to the right of the key turns off. To adjust the heating power or stop cooking, just press key : for 2 seconds: the controls are enabled again. Safety devices Several safety devices have been fitted onto the hob to protect its electronic components. After unlocking the control panel if no keys are pressed for 30 seconds (no cooking zones in operation), the unlock indicator light turns off: the hob is locked. [. . . ] ) placed for more than 10 seconds on the control zone, L boiled-over liquids or food spilled on the control zone, L extended pressure on the control zone, could cause the beep to sound, followed by the three power level displays blinking, the cooking zone(s) in use turn off. To stop the beep from sounding, remove the cause of the malfunction, for 2 seconds: you can control the cooking zones again. To put a stop to the blinking, press key Overheating Prolonged use of the hob could cause the electronic components to overheat. A thermal protection device momentarily sets a reduced power (setting 3) on the back right cooking zone. The power level displays blink to advise you that this safety measure has been taken. When the temperature has gone back to normal, the power level displays stop blinking and the zone can be used at higher power settings if need be. 55 Using the cooking zones Cooking zone description • The "Quickring" radiant zones comprise circular heating elements whose filament turns red. Cooking zone control The cooking zones feature touch controls to ensure the correct supply of energy according to time: the cooking zones do not heat constantly, but rather in pre-set sequences. This feature has many advantages: the utmost reliability, extremely quick temperature rises and accurate control, ideal for cooking over very low heat and for delicate dishes. ) fierce (fish , omelettes , etc) moderate - simmering (pasta and rice on reaching boiling point , potatoes , stews , blanquette , vegetables , fruit , soups , sauerkraut , hotpots , etc. However, we do recommend you use saucepans with a thick and very flat base - such as copper and stainless steel sandwich bases or heavy duty bases tapered slightly inward for example - and to avoid at all costs all cookware with irregular rough bases which could scratch the glass surface. 57 Technical information for the fitter Read this chapter carefully, as it contains vital information for a safe and secure installation. recommendations · The appliance must be installed by a qualified technician in compliance with the instructions provided by the manufacturer. The latter denies all responsibility for improper installation which may harm persons and animals and damage property. When you have removed the packing, check whether the appliance is intact. Never leave the packing components (plastic bags, polystyrene foam, nails, etc. ) within the reach of children since these are a source of potential danger. Built-in installation This hob can be built into a worktop simply by cutting out the corresponding slot. All support types are suitable: only some plastic materials are unadvised, as heat of up to approximately 100°C could cause their deformation. Make sure you leave 4 cm of room between the rear cut-out of the hob and the back of the worktop, to avoid burning the wall or the backsplash, especially if the latter is laminated. 595 40 15 48 56 0+ /- 1 0 49 +/- 1 Built-in installation type Y (IEC 335-2-6 Norm) If the hob is fitted above an oven, in order to avoid any overheating on the part of the hob's electric components, it is vital that you leave a space 560mm wide and 8mm high between the top edge of the oven and the bottom of the worktop. If this is unavoidable, place a watertight separating element between the two appliances. [. . . ] If this is unavoidable, place a watertight separating element between the two appliances. 58 8 mm 51 0 Fastening the hob Very important: : It is vital that you ensure the glass ceramic hob is built into a perfectly flat supporting surface. Deformations due to improper fastening could alter the characteristics of the hob and compromise its performance. Take particular care in ensuring the seal surrounding the hob is correctly in place, in order to avoid any leaks into the supporting cabinet. [. . . ]