User manual IROX HBVR761

[. . . ] N [SNOOZE/LIGHT] BUTTON Activate the snooze function and backlight O WALL-MOUNT RECESSED HOLE For mounting the main unit on a wall P BATTERY COMPARTMENTS Accommodates two UM-3 or "AA" size 1. 5V batteries Q REMOVABLE TABLE STAND For standing the main unit on a flat surface MAIN FEATURES: THERMO/HYGRO REMOTE UNIT WIRELESS THERMO · HYGRO E AC RESET 123 CHANNEL 1 2 3 F D B MAIN FEATURES: UV REMOTE UNIT B A A LED INDICATOR Flashes once when the remote unit transmits a reading. C RESET BUTTON Press to reset all setting if you have selected different channel. D CHANNEL SELECTOR Select the channel before you install batteries. NOTE: LED INDICATOR ON TOP SIDE Flashes once when the remote unit transmits a reading Flashes twice when low battery is detected on sensor unit A BATTERY COMPARTMENT Accommodates 2 UM-3 or "AA" size 1. 5V batteries. B LED INDICATOR Flashes once when the remote unit transmits a reading. [. . . ] If you travel with become impossible due to changes in altitude and location. You'll have to wait up to 24 hour so that the weather station can calculate a new forecast based on the conditions at the new location. 87 3b) BAROMETRIC PRESSURE TREND The atmospheric pressure indicator, in the weather forecast window, uses arrows to indicate if the atmospheric pressure is increasing, remaining stable, or decreasing. Arrow indicator Pressure Trend TREND TREND TREND Rising Steady Falling The atmospheric pressure can be displayed in mb/hPa or inHg. To change the pressure unit, press and hold the [UNIT] key at sea level pressure display and use [ ] or [ ] (rear panel) key to select. If you want to check the pressure history for a particular hour during the past 36 hours, press the [HISTORY] button. The recorded atmospheric changes for the past 24 hour are displayed in a bar chart above the atmospheric pressure window. 4. UV-MEASUREMENT 3c) HOW TO CHECK THE BAROMETRIC PRESSURE 4a) Description The UV-Index (UVI) is an international standard defining the intensity of the UV radiation of the sun. The higher the UVI, the stronger is the UV radiation of the sun and therefore potentially harmful to humans. The UVI makes you aware of this and helps you to choose the correct protection. 4b) UV table and display indicates UV-Index Symbol Level Intensity weak Protection No protection necessary 0 -2. 9 3 - 5. 9 medium Protection necessary: Hat, t-shirt, sun glasses, sun cream The current and historical barometric pressure is shown on the atmospheric pressure window. For user staying at a higher altitude such as in the mountain area, see-level barometric pressure applies. Use [PRESSURE / ALTITUDE key to toggle the display to sea level pressure display. Press and hold the Pressure/Altitude key to enter the sea level pressure adjusting mode. Use the [ ] or [ ] (rear panel) key to enter sea level pressure and use [PRESSURE/ALTITUDE] to confirm. 88 6 - 7. 9 high Protection necessary: Hat, t-shirt, sun glasses, sun cream 8 - 10. 9 very high Additional protection necessary: Avoid to stay in unprotected areas 11+ extreme Additional protection necessary: Avoid to stay in unprotected areas 89 5. THERMOMETER / HUMIDITY 5a) HOW TO CHECK REMOTE AND INDOOR TEMPERATURES The wave display on the outdoors temperature indicates the reception of the remote unit is in good order. If no readings are received from the remote unit for more than two minutes, blanks " " will be displayed until further readings are successfully searched. You can wait for a little while or Hold [ ] for 2 seconds to enforce an immediate search. If the temperature or humidity goes above or below than the measuring range of the main unit or the remote unit (stated in specification), the display will show " " & "HHH" or "LLL" respectively. The unit can be set to automatically scan and display readings from the remote sensors, the display will show the readings from one channel for about 4-seconds and then proceed to the next channel display. -To activate the remote-sensor scanning mode: Press and the hold the button [CHANNEL] for 2 seconds. -To deactivate the remote-sensor scanning mode: Press and the hold the button [CHANNEL] for 2 seconds. 5b) HOW TO READ THE KINETIC WAVE DISPLAY The kinetic wave display shows the signal receiving status of the main unit. No signals. 5c) MAXIMUM AND MINIMUM TEMPERATURES AND HUMIDITY The maximum and minimum recorded indoor temperature, humidity and outdoor temperatures will be automatically stored in memory. [. . . ] SPECIFICATIONS Temperature Measurement Main unit Indoor Temperature measurement Proposed operating range Humidity Measuring range Temperature resolution Humidity resolution Barometric Pressure Measurement Pressure measuring range : 750 to 1100 mb/hPa at 25°C (22. 15 to 32. 49 inHg) Pressure sampling cycle : 20 minutes Moon Phase Functions Moon Phase Scanner Range : forward/ backward 39 days 96 : 0°C to +50. 0°C 32. 0°F to 122. 0°F : R. H. 10% to 95% at 25°C ( 77°F ) : 0. 1°C 0. 2°F : 1% R. H. PRECAUTIONS This product is engineered to give you years of satisfactory service if you handle it carefully. They may scratch the plastic parts and corrode the electronic circuit. Do not subject the unit to excessive force, shock, dust, temperature or humidity, which may result in malfunction, shorter electronic life span, damaged battery and distorted parts. [. . . ]