User manual IROX HBR325P

[. . . ] Press and hold in the displayed mode: Enter Set-Up or change the unit. E MEM BUTTON Shows records for moon phase, temperature/humidity, sunrise/sunset F HISTORY BUTTON Enters weather mode and then shows history for the sea-level pressure (past 24h) G CHANNEL BUTTON Changes temperature and humidity display to selected channel Press and hold to enable cycling display of channel temperature and humidity. H (-) BUTTON - Switches to next mode in clockwise direction - Decreases the value in any setting mode - Activates sensor search (hold key in Thermo mode) - Thermo Alarm ON/OFF (Thermo Mode; Alarm setting) I (+) BUTTON - Switches to next mode in anti-clockwise direction - Advances the value in any setting mode - Starts RC reception (hold key in Time Mode) - Thermo Alarm ON/OFF (Thermo Mode; Alarm setting) J BATTERY COMPARTMENTS Accommodates 4 UM-3 or "AA" size 1. 5V batteries K DC JACK Plug-in for the 7. 5V 200mA transformer HBR325P Operating Instructions 2 IROX TE657 & TS33C MANUAL (ENG) SIZE: W65 X H105 (mm) BY WING TSUI 13/06/08 5 6 1. Soft-touch button design provides you a novel key interface and outlook design. [. . . ] Set Local Pressure Units: Press "+" or "-" to adjust. In Pressure and Weather Forecast Mode, press SET until Sea-Level Pressure is displayed. Set Sea-Level Pressure Units: Press "+" or "-" to adjust. In Pressure and Weather Forecast Mode, press SET until the set altitude is displayed. Set Altitude Units: Press "+" or "-" to adjust (feet or meter). When sea level pressure is displayed, press HISTORY repeatedly to view sea level pressure data for each of the last 24 hours. If no buttons are pressed for 5s, the display automatically returns to Pressure and Weather Forecast Mode. g) Viewing the Pressure/ Temperature/ Humidity Bar-Charts The bar-chart on the display can be configured to display the history data for sea-level pressure, temperature or humidity for channel 1. In Pressure and Weather Forecast Mode, press and hold ALARM/CHART, to toggle the bar-chart between: - Sea-level pressure ("PRESSURE" will be displayed) - Temperature (Thermometer icon and "CH1" will be displayed) - Humidity (RH icon and "CH1" will be displayed) h) Weather forecast The unit is capable of detecting atmospheric pressure changes. Based on collected data, it can predict the weather for the forthcoming 12 to 24 hours. Symbol of Display Forecast Symbol of Display Forecast Heavy Rainy Heavy Snowy Storm Sunny Slightly Cloudy Cloudy Little Rainy - Lower Temperature Alert (displays OFF if deactivated): icon displayed When the above alerts are displayed, pressing "+" or "-" will activate/deactivate the corresponding alert. · Temperature Alarm The temperature alarm will sound when the temperature is out of the pre-set range. Set Daylight Saving Time Option: Press "+" or "-" to turn DST option on or off. The various options you may find in the Appendix in the "DST definition". Note: You may press and hold SET anytime during the setup to return to the normal Clock and Alarm Mode. The same will happen, if you do not press any key in the setting mode for more than 2 minutes, extreme caution 32 ­ 41°C danger extreme danger 41 ­ 54°C > 54°C 6. SUNRISE AND SUNSET MODE Important: All operations described in here are to be made in the Sunrise/Sunse mode The main console unit computes the sunrise and sunset times from the user-configured location data. This includes the longitudes, latitude, time zone and DST (Daylight Saving Time). Choosing a suitable city code for your location will automatically generate the correct values for the location data. Should you wish to input your own location data or if a suitable city code could not be found, choose "USR" as the city code during setup. A searching function is also available, which allows the sunrise/sunset times for different dates to be viewed. a) Accessing Sunrise/Sunset Mode From the main console unit: Press "+" or "-" until the sunrise and sunset icons on the lower left of the display start flashing. 17 18 22 b) Setting up the Location Data i) In Sunrise/Sunset Mode, press and hold SET to enter location data setup. ii) The city code in the Time and Alarm display should start flashing. [. . . ] · Single Alarm " " The alarm sound will be activated and the icon will be flashed when it is armed and the alarm time is reached. Once it finished, it will be disabled automatically · Pre-Alarm "Pre-AL" The pre-alarm sound will be activated and the icon will be flashed if the temperature of channel 1 is under or equal two degree C. It is programmable 15, 30, 45, 60 or 90 minutes earlier than the weekday alarm or single alarm time. 24 20 23 Disabling/Entering Snooze when Time Alarms are activated To Enter Snooze: Press SNOOZE to enable snooze function. Note: Alarm will automatically enter snooze mode if no key is pressed after the alarm sounds for 2 minutes. [. . . ]