User manual IROX ETHG889

[. . . ] Press C to advance to the next setting as in the following: HOUR C C 12/24 H MINUTE C C DAY SECOND C C MONTH YEAR C * When second digits are flashing, press A or B to reset the digits to 00. Resetting seconds when the digits are between 00 to 29 will leave the minute digits unchanged, or between 30 to 59 will increase the minute digits By one. * When 12 or 24 is flashing, press A or B to switch between 12- or 24-hour formats. Press D to exit the setting screen and day of the week will be adjusted automatically. [. . . ] * Reading shown indicates the direction that the LCD's 12 o'clock position is pointing to. ­ Declination correction is provided. 102 * Declination is the difference between true north and magnetic north. Compass readings are easily affected by disturbing sources of magnetism, so the compass should always be used in the open air. Hold down D until "CAL" is shown on the display, which indicates the calibration screen. Press D and the ten-degree digit starts to flash on the display, which indicates the declination angle setting screen. * Press A will end calibration skipping the declination angle setting. Press C to advance to the next setting as in the following: C TENS OF DEGREE C DEGREE C E/W 103 * When E or W is flashing, press A or B to switch between East and West. * You should consult your local organization for information of declination. Declination angles for major cities are listed below for reference only. City Anchorage Atlanta Auckland Berne Bombay Boston Calgary Canberra Chicago Denver Declination City Angle 22° E 4° W 19° E 0° E 1° W 16° W 18° W 12° E 3° W 10° E Declination City Angle Declination Angle Jerusalem 3° E London Little Rock 4° W 3° E Rio De Janeiro 21° W San Francisco 15° E Seattle Shanghai Stockholm Toronto Vaduz Vancouver 19° E 5° W 4° E 11° W 0° E 20° W Livingston, MT 14° E Munich 1° E New York City 14° W Orlando Oslo Paris Reykjavik 5° W 2° W 2° W 19° W Washington DC 10° W Wellington 22° E 104 6. * If "ERR" indicating error is displayed, calibrate the compass again. To clear the altitude data Hold down D until "----" is shown on the display to clear all altitude data stored. * Altitude data cannot be cleared individually. 112 9 CHRONOGRAPH MODE Lap time indicator Lap time Split time Lap number Split time indicator Use C to enter Chronograph mode. ­ The chronograph is of 1/100-second resolution for the first hour and 1second resolution for the rest and with working range up to 24 hours, then the chronograph stops automatically. ­ For the first hour, the chronograph shows minutes, seconds and 1/100seconds, then it shows hours, minutes and seconds. ­ There are 100 memories for lap/split times stored in a maximum of 30 runs. ­ The chronograph lets you measure elapsed time, lap/split times and two (or more) finishes. 113 * When you take lap/split times, the display will be frozen to show lap time, split time and lap number for about 6 seconds, then the display will show the current running times automatically. * Data of the current run is stored and chronograph is reset to all zeros. * All runs are cleared. 118 11 ALARM MODE T1 indicator Alarm 1 indicator Alarm time ON/OFF status indicator Chime on indicator Alarm on indicator Use C to enter Alarm mode. ­ There are 2 daily alarms and they can be set to refer to Normal Time (indicated by T1) or Dual Time (indicated by T2). ­ Daily alarm sounds at the same time each day, while it is turned on. ­ The alarm sounds at the preset time for about 20 seconds, or until you stop it by pressing any button. [. . . ] To switch between alarm 1 and alarm 2 Press B to switch between alarm 1 (indicated by AL-1) and alarm 2 (indicated by AL-2). Hold down D until the hour digits start to flash on the display, which indicates the setting screen. Press C to advance to the next setting as in the following: C HOUR C MINUTE C REFER TO T1/T2 C CHIME ON/OFF * When TIME 1 or TIME 2 is flashing, press A or B to switch between setting the alarm to refer to Normal Time (TIME 1) and Dual Time (TIME 2). * When ON or OFF is flashing, press A or B to turn the chime on (indicated by ON) and off (indicated by OFF). 120 If chime is turned on, the chime on indicator will be shown after exiting setting screen. [. . . ]