User manual IQUA 603 SUN QUICK GUIDE

[. . . ] Indicator light Status indication with blue and red light Sales package contents a. 5 (H) mm 14g Up to 12hours depending on ambient light Infinite depending on ambient light Within 2h Li-Polymer battery a-Si Bluetooth Specification 2. Getting started Charging the battery Before using Iqua 603 SUN for the first time, you must charge it for approximately 2 hours. When the battery is fully charged, it provides up to 12 hours of talk time and an unlimited standby time depending on the ambient light. [. . . ] User wearing the headset walks away from the phone), the headset will be disconnected from the phone and user will hear a warning tone from the headset. Headset is now in "powered on but no Bluetooth connection" ­mode (blue light flashes once every 5 seconds). If the headset is back in range within 10 minutes, Iqua 603 SUN auto-reconnects with the last phone. If the headset is out of range for over 10 minutes, long press both Multifunction and Volume + buttons or both Multifunction and Volume ­ buttons to reactivate the connection. Call Functions Answer a call Press the Multifunction -button shortly to answer an incoming call. End a call To end an active call, press shortly the Multifunction -button. Reject a call When you receive an incoming call that you do not want to answer, double press the Multifunction-button to reject. Redial the last dialed number Press and hold the Volume+ button until you hear a tone. *With some phone models, press the Volume + button again to dial the number displayed on the phone. Voice dialing (when supported by the phone) Press and hold the Volume ­ button until you hear a tone (Voice Dial feature activated on the phone), speak the voice tag. Mute & un-mute During an on-going call, press and hold both Multifunction and Volume + buttons until you hear a tone. Switch between phone & headset To transfer call from Iqua 603 SUN to your phone or vice versa, press and hold both Multifunction and Volume ­ buttons. Once it is already paired to 8 devices, the 9th paired device will replace the 1st paired device. You can also erase the paired device list of the headset in order to pair it with new devices. While the headset is powered on but not connected with any Bluetooth device, press and hold the Volume + button for 5 seconds until you hear a tone. Light indication summary The Iqua 603 SUN's LED lights can be blue or red and are usually accompanied by a sound signal. Power on / off Blue LED flashes once/Red LED flashes once Powered on but no Bluetooth connection Blue LED flashes once every 5 seconds Connection active Blue LED flashes twice every 8 seconds Pairing mode Blue and red LED flashes alternately Battery low Battery low tone is played Battery charging Red LED is on continuously Power management This product is powered by a built-in rechargeable battery and a solar panel which can not be changed. Rechargeable battery can be charged and discharged hundreds of times, but it will eventually wear out. After a period of time that will vary depending on the use and usage conditions you may find that the built-in battery will power your product for only a couple of hours requiring you to charge more frequently. Do charge your device only with the charger provided in the sales package. Do not leave the device connected to the charger for longer period than needed, since overcharging may shorten the battery lifetime. If left unused, a fully charged battery will discharge itself over time. [. . . ] , declare under our sole responsibility, that the product, BHS-702, conforms with the provisions of the following Council Directive: 1999/5/EC. 1 Point-to-point Upp till 8, en åt gången 10 meter 0°C till 45°C -20°C to 55°C Para din Iqua 603 SUN till din mobiltelefon Parning är en process där du sammanlänkar Iqua 603 SUN till en kompatibel Bluetooth mobiltelefon. Din Iqua kan sammanlänkas till upp till åtta (8) mobiltelefoner men den kan bara vara parad med en telefon åt gången. Se användarmanualen till din mobiltelefon för information om hur du söker och parar till externa enheter. [. . . ]