User manual INTERMATIC ST01C

[. . . ] NOTE: Your switch timer automatically skips any conflicting ON event as summer approaches to prevent unwanted operation of lights or other controlled devices. See "What to Do" if you want to identify and remove conflicting settings. Switch timer does not "catch up" automatically to the programmed load state. The status of the switch timer will remain as is until it comes to the next programmed ON/OFF time. [. . . ] The switch timer should "click. " NOTE: If display doesn't flash "12:00 am", the battery may be dead. 2 ­ Install the Switch Timer and "C" to the "Common" terminal of your remote switch, using the supplied piece of jumper wire, if necessary. Follow diagram # 3 below, if using a new single-pole remote switch. LOAD BLACK TIMER RED NOT USED WIRE "A" BLUE WIRE "B" WIRE "C" JUMPER NEUTRAL The switch timer ignores a 3-way remote switch even though it is wired correctly. DIAGRAM 2: LINE 2-SWITCH SETUP, TIMER INSTALL RE-USING EXISTING REMOTE 3-WAY SWITCH 3-WAY REMOTE SWITCH "COMMON" TERMINAL LOAD The load turns off immediately after being turned on. DIAGRAM 3: 2-SWITCH SETUP, TIMER INSTALL USING NEW SINGLE-POLE REMOTE SWITCH LINE BLACK TIMER BLUE WIRE "B" WIRE "C" JUMPER NEUTRAL RED WIRE "A" SINGLE-POLE REMOTE SWITCH The battery tray is difficult to replace. The switch timer operation is sluggish or not switching ON/OFF at all. Timer shows ON but the light or other controlled device is OFF. Seat the battery in the tray, then reinstall. The timer should "click. " Make sure the light or controlled device is switched ON and plugged in. LIMITED ONE-YEAR WARRANTY If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs, LED's and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs. INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. This feature North tracks changes in sunrise Center Center and sunset times. Press + to select your local zone: NoRTH, CENTer, or SOUth South South (Fig. You can set DAWN or DUSK to your exact time in your area according to your newspaper or online. Use the following procedures to do so, or press ON/OFF 3 times to skip. CHECK YOUR SETTINGS: Press ON/OFF repeatedly to loop back around to review your date and time settings. 6 ­ Set Initial Pair of ON and OFF Times You have many options with up to 40 timer settings: · Set to a specific ON/OFF time. · Set to DAWN and DUSK, which automatically adjust as the seasons change. · RANDom -- gives your home a "lived-in" look by varying your settings by a random amount of ± 20 minutes or so. · MANual -- makes the switch into a standard ON/OFF switch without timer settings. About the Battery · · · LINE · · · · · For four or more switch setups: Use the preceding 3-switch installation diagram and wire 4-way switches between the two 3-way switches. NOTE: The remote switch(es) may not function reliably when the accumulated wire length to the remote switch(es) exceeds 100 feet or if the wiring to the remote switch(es) is buried underground. [. . . ] For example, in SET UP mode, you will see HOUR, MINute, AM/PM, Year, MONth, etc. Use the + or ­ buttons to change a setting when it is FLASHING (e. g. , the correct hour). Pressing ON/OFF again advances to the next setting and automatically saves -- whether you changed the setting or not. If you're interrupted during programming, your work to that point is automatically saved after 5 minutes. [. . . ]