User manual INTERMATIC ST01

[. . . ] Troubleshooting Guide Observed Problem Switch timer does not switch ON/OFF but display looks normal. Switch timer won't enter AUTO or RANDom mode when you press MODE. Possible Cause Switch timer is not set in AUTO, RANDom, or MANual mode. Switch timer is in RANDom mode, which varies switching times up to ±20 minutes (to give your home a "lived-in" look). For example, you've set ON to DUSK and OFF at 8 pm, and due to seasonal changes, DUSK has advanced to 8:30 pm. [. . . ] SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd. , Spring Grove, Illinois 60081-9698/815-675-7000 http://www. intermatic. com Please be sure to wrap the product securely to avoid shipping damage. 1. Turn off power at the service panel by REMOVING FUSE or TURNING THE CIRCUIT BREAKER OFF. 2. Trim building wires to 7/16" as shown. If a Single Switch Setup: 7/16" g. Connect one of the two wires BLACK WIRE INTERMATIC INCORPORATED SPRING GROVE, ILLINOIS 60081-9698 158ST13133 from the wall to the black wire from the switch timer, using the twist connectors provided. Connect the other wire from the wall to the blue wire from RED WIRE the switch timer, using the (capped, not connected) twist connectors provided. Cap with a twist connector. NOTE: For new construction or to replace a dimmer switch, a lighted switch, or a 3-way switch without screw terminals, a single-pole switch can be used at the remote location, as shown. NOTE: If the building's wiring colors don't allow you to tell wire "A" from "B, " just pick one of the two wires and connect as if it is wire "B. " After the installation is complete, if the controlled light or device will not turn on properly, simply reverse wires "A" and "B. " See Steps J and K for how to check. Using screws provided, mount the switch timer into the wall box, then install the wall plate. Do the following test with the remote switch in each of its 2 positions: Press the ON/OFF button on the switch timer several times. Each time that you push the ON/OFF button, the switch timer should "click" and the controlled light or device (the "load") should turn on or off. - If the timer clicks but the load does not operate, re-check your wiring and make sure the load is functional. If the timer clicks but the load only operates when the remote switch is in one of its 2 positions, you need to turn off the power at the service panel, then reverse wires "A" and "B. " You can reverse wires "A" and "B" at the remote switch wall box, or you can reverse wires "A" and "B" where they connect to the red and blue wires of the switch timer. Verify that the controlled load turns on or off each time that the remote switch is operated. If a Multiple Switch Timer Setup: Multi-switch applications using the ST01 Series switch timer are wired differently than when using conventional toggle switches. · Multiple switch timers may be mounted in an unlimited number of adjacent junction box slots. Programs are created in two procedures: setting an ON time followed by setting an OFF time. The instructions below will guide you as follows: · First, for setting an ON time, which can be DAWN or DUSK, or a specific time such as 6:00 pm, · Then for setting an OFF time which can also be DAWN or Dusk, or a specific time. then press + until you see the program number you want to set (Fig. Press ON/OFF, then press + if necessary, to display ON for setting the ON time (Fig. Continue to press + for OFF (if setting an OFF time) or SKIP (if deleting a setting). Press ON/OFF, then press + to display whether you want ON to be set for DUSK, DAWN, or a specific time which would be shown as "12:00" (until you change it). If ON is to be at Dawn or Dusk: NOTE: Some people like to set DUSK as an ON time and match it with a specific time such as 11:00 pm for OFF. [. . . ] Press MODE when you're finished to navigate to the mode you want to operate the switch timer: Auto, Manual, or Random. a. Press ON/OFF to set your exact local time 4 ­ Clear Any Existing Programming It's unlikely that the new switch timer has any existing programming but to make sure, use this procedure before setting the time. Using a pen or paper clip, press and release RESET, which is the small round button to the lower right of the + button. The screen will initialize, then flash "12:00 am" in MANual mode. [. . . ]