User manual INTERMATIC SS7C

[. . . ] Place battery in holder with "+" end towards front of timer. Battery Holder MO ON MODE ON/OFF EVENT RESET DAY H+ M+ DAY H+ M+ 4b 2 5 Push Buttons: MODE ON/OFF EVENT RESET RESET button RESET Recessed so you don't push it accidentally. Push and release to reset: When you press RESET: · The mode switches to MAN. · All programmed ON or OFF times are set to null (at null, no switching occurs, clock displays -:--). [. . . ] High or low temperature or frequent use of the manual pushbutton or the 3-way switch will reduce the battery life. Replace the battery when the digital display is dim, the message `lobAt' (Meaning LOW BATTERY) is displayed, or if the timer fails to operate. The timer has built-in memory protection providing at least 15 seconds to change a weak battery without losing your settings. You do not need to turn off the load or the power in order to replace the battery, however, do not attempt to switch the timer on or off while the battery is out or your settings will be lost and the timer will need to be reset. Function depends on the mode: CLK mode - ON/OFF EVENT button does nothing. PGM mode - Switches in order through the 12 programmable events 1 ON, 1 OFF, 2 ON, 2 OFF, 3 ON, 3 OFF, 4 ON, 4 OFF, 5 ON, 5 OFF, 6 ON, and 6 OFF. MAN mode - Manually turns switch on or off. How to set or change the clock 1. Push and release DAY button until correct day of week is displayed (3a). Push and release clear cover/switch to switch load ON or OFF if necessary. 2a CLK 4a 3a 2, 6 3 4 PM WE ON 5a ON/OFF EVENT MODE RESET DAY H+ M+ Programming and Operating Instructions Introduction to Operation and Programming: The timer is a programmable switch. At any time you can push the clear cover/switch to manually turn the switch ON or OFF, unless selected mode is CLK or PGM. You can program up to 12 ON/OFF EVENTS; times when the timer automatically switches the connected lights (or other electrical devices) ON or OFF (up to 6 ON events and 6 OFF events). An EVENT can be set to switch at: · any specific time, and day of the week, · a specific time every day, · a specific time on weekdays, or · a specific time on weekends. See Installation Instructions first if your timer is not already installed, or if the AA Alkaline battery is not installed. 5 How to set, change, or review ON/OFF times 1. If necessary, push and release ON/OFF/EVENT button until event to set/change is displayed (3a), or push the ON/OFF/EVENT pushbutton repeatedly to review all the ON/OFF times. Push and release DAY button until desired day or group of days is displayed (4a), or push and release the DAY button until "-:--" is displayed, if you would like to cancel this ON or OFF time. Push and release H+ button until desired event hour and AM/PM are displayed (5a). Push and release ON/OFF/EVENT button to choose the next event to set 5a or change (7a). Push and release clear cover/switch to switch load ON or OFF if necessary. PGM 3a ON 3, 7 MODE ON/OFF EVENT RESET DAY H+ M+ 6 5 6a 7a PGM OFF PM MO TU WE TH FR Manual Override Works like a light switch. Push and release the clear cover/switch (area over buttons) to switch ON or OFF. Or switch ON and OFF using the remote switch(es) in multi-switch installations. · · · · Works in AUTO, AUTO RAND or MAN modes. The program in AUTO or AUTO RAND remains; it automatically switches ON or OFF at next programmed time. AUTO RAND PM WE ON (Example) LOAD MAINTENANCE WARNING1 DO NOT USE THE TIMER TO TURN OFF POWER FOR MAINTENANCE (repairs, removing broken bulbs, etc. ). ALWAYS TURN POWER OFF AT THE SERVICE PANEL BY REMOVING A FUSE OR SWITCHING OFF A CIRCUIT BREAKER BEFORE DOING ANY CIRCUIT REPAIRS. MODE ON/OFF EVENT RESET DAY H+ M+ PUSH ON/OFF Error Messages The `lobAt' message means the battery is low and needs to be replaced. [. . . ] Excessive length of wire (greater than 30 feet) or buried wiring to the remote switch. Remote switch is defective or worn out. Load turns off immediately after being turned on. Remote switch or timer wired incorrectly, excessive length of wire (greater than 30') or buried wiring to remote switch, or defective timer. Battery not seated in holder, holder misaligned, or contact tabs of holder are bent. Battery holder is difficult to snap in place FULL ONE YEAR WARRANTY If within one (1) year from date of purchase, this product fails due to a defect in materials or workmanship, Intermatic Incorporated will repair or replace it free of charge. The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping; (b) units which have been subject to unauthorized repair, opened, taken apart; (c) units not used in accordance with directions; (d) damages exceeding the cost of the product. [. . . ]