User manual INTERMATIC HA09

[. . . ] 11 Remote ON/OFF/DIM Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Resetting the Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Resetting the CHANNELS only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Additional Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] All modules must be assigned to the master controller before any programming or remote control functions can be accomplished. Page 6 of 20 ____________INCLUDE Modules to a Network_________ NOTE: Devices should be plugged into modules before adding modules to the network. (See Fig 3a) While holding the door grips, slide the cover down to reveal the INCLUDE and DELETE buttons. The green LED will flash indicating that the controller is ready to add modules to the system. (If the green LED stops flashing, the controller has "timed out". The INCLUDE button must be pressed again). Page 7 of 20 2. Fig 3a. Press and release the INCLUDE button Creating a Network (continued) 3. If successful, the LED on the controller and module will turn solid green. If not successful, the red LED will flash and it will be necessary to repeat steps 2 and 3 until the green LED on the controller turns solid green and does not flash. Repeat steps 2 and 3 for each module you wish to include into the network. Fig 3c. Press and release the programming button 4. Page 8 of 20 1. 2. 3. Associating Modules to Channels (See Fig 4a on page 10) On the remote controller, simultaneously press and hold the ON and OFF buttons of the desired channel. (See Fig 4c on page 10) While holding the INCLUDE button, press the program button on the module. Choose a light level holding the module PROGRAM 4. 5. button until you have set the desired light level. Possible settings are FULL ON, FULL OFF or DIM LEVEL for dimmable modules, (NOTE: Only HA03 Lamp Module and HA06 In-Wall Switch/Dimmer have dimming capabilities) or FULL ON, or FULL OFF for non-dimmable modules. After setting your desired light level, release the INCLUDE button on the remote controller. To include additional devices to the channel, repeat steps 1 ­4. Page 9 of 20 Associating Modules to Channels (continued) Fig 4a. Press and release the programming button Page 10 of 20 Exclude from Network (See Fig 5a and 5b) Follow the same procedure as Creating a Network except press the DELETE button instead of the INCLUDE button. Exclude from Channel (See Figures 6a, b, c) Follow the same procedure as Associating Modules to Channels except press and hold the DELETE button instead of the INCLUDE button. Fig 5a. Press and release the programming button Fig 6a. Press and hold Channel ON and OFF until LEDs flash. Page 11 of 20 Fig 6b. Press and hold the DELETE button. Fig 6c. Press and release the Programming Button. Remote ON, OFF, DIM Operation (See Fig 7) ON ­ Press and release the ON button for the assigned channel. Release the button when you have achieved your desired light level. Fig 7. Press and release the ON/OFF/DIM buttons to turn ON or OFF your device. Press and hold the ON/OFF/DIM buttons to dim your device. CONGRATULATIONS!You have completed the programming of your HA09 Handy Remote controller. Page 12 of 20 Resetting the Controller If needed, you can reset the NETWORK and CHANNEL settings individually or both together. [. . . ] Made in China. Page 19 of 20 LIMITED 6 YEAR WARRANTY If within six (6) years from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, as its sole option, free of charge. This warranty is extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs, LED's and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs. INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. [. . . ]