User manual INTERMATIC HA07

[. . . ] With these products you can reliably and remotely control lighting and appliances. The outstanding features of the Home Settings program include: Feedback that will allow you to see whether your device has received the ON/OFF/DIM signal. Ease of installation Manual override RF signal reliability ­ each Home Settings product has a special repeater feature that virtually guarantees that RF signals are received. MODEL HA07 - MASTER CONTROLLER INSTRUCTIONS Page 1 of 35 158HA11645 The HA07 Controller also includes the following features: 12 Channels - each channel can control up to 16 devices to create scenes or timed events. [. . . ] Zones are divided between North, Central and South (See Fig 5d). Page 11 of 35 3. 4. Fig 5a ­ SETUP mode Fig 5b ­ dST setting Setting Daylight Saving Time (dST) and Zone (cont'd) Fig 5c ­ Press ENTER to accept zone setting. Fig 5d ­ Zone Map Page 12 of 35 Setting Astronomic Function NOTE: If you do not want to use the Astronomic function, you can bypass SETUP mode by pressing the MODE button until program (PGM) mode is displayed. If the time is not correct, or if you would like to customize the SUNUP time, press + or - to enter the desired time and press ENTER. If the time is not correct, or to customize this time, press + or - to enter the desired time and press ENTER. Page 13 of 35 3. 4. Fig 6 ­ SUNUP default time may be different than shown above. Setting Astronomic Function (continued) Fig 7 ­ SUNSET default time may be different than shown above. Press ENTER to accept the default time. Creating a Network NOTE: Creating a network refers to assigning modules to the master controller. All modules must be assigned to the master controller before any programming or remote control functions can be accomplished. NOTE: Devices should be plugged into modules before adding modules to the network. The INCL icon and TRANSMITTING message will begin to flash, indicating that the controller is ready to include modules to the system. (If INCL and TRANSMITTING stop flashing, the controller has "timed out". The INCLUDE button must be pressed again). Page 14 of 35 INCLUDE Modules to a Network (continued) 2. If successful, the INCL icon will stop flashing and the word SUCCESSFUL will show for 2 seconds. If NOT SUCCESSFUL appears on the screen, it will be necessary to repeat this step until SUCCESSFUL appears. Repeat steps 1 and 2 for each module you wish to add to the network. Fig 8a ­ Press and release the INCLUDE button Fig 8b ­ Press the PROGRAM button Page 15 of 35 Associating Modules to Channels 1. (See Fig 9a) On the remote controller, simultaneously press and hold the channel ON and OFF buttons of the desired channel. Release the ON and OFF buttons after "LEARN" appears in the display. You may now set a scene for your channel by pressing the PROGRAM button on the module until you reach your desired light-level setting. Setting different light levels for different modules allows you to create "scenes" for each channel. NOTE: Only HA03 Lamp Module and HA06 In-Wall Switch/Dimmer have dimming capabilities. After you release the INCLUDE button, the controller will store the current light-level and SUCCESSFUL will display on the controller for 2 seconds and the module LED will flash for 2 seconds. To add additional devices, repeat steps 1 ­ 4. Associating Modules to Channels (continued) Fig 9a ­ Press and hold the channel ON and OFF buttons. Release buttons when "LEARN" is shown in the display. Fig 9b ­ Press and hold the INCLUDE button. Fig 9c ­ Set the desired light level by pressing the PROGRAM button on the module. 4. __INCLUDE Modules to the ALL ON/ALL OFF feature:__ Fig 13a ­ Press and hold the ALL ON and ALL OFF buttons Fig 13b ­ Press and hold the INCLUDE button Fig 13c ­ Press the PROGRAM button until ALLSET appears. Page 21 of 35 EXCLUDE Modules from the ALL ON/ALL OFF Feature 1. [. . . ] The display will read, "ALL CLEAR". 2. Troubleshooting Problem: · Every time I try to INCLUDE or DELETE modules to my network, I keep getting errors (red LED flashes) Solution: · The controller might be a Secondary Controller. Only a Primary Controller may be used to INCLUDE or DELETE modules into or from a network. Reset the module by pressing and releasing DELETE on the primary controller, then push the program button on the module. · You have copied from the wrong controller and overwritten your primary controller. · After I perform a controller replication, neither controller controls anything at all. Page 32 of 35 Troubleshooting Problem: · I am trying to turn on a module associated to channel 1, but it will not turn on. Solution: · Check to be sure there is power supplied to the module. [. . . ]