User manual INTERMATIC DT1

[. . . ] 8 DS button - push and hold for a couple of seconds to switch to or from daylight savings time. 9 PROG button - push and release to set or change programmed on and off times. 10 MODE button - push and release to choose the mode. AM PM Prg TIME SET Off Auto On Rand PROG ON/OFF HOUR MIN DS PROG MODE AM Daylight Savings Time In Off, Auto, or On mode, push and hold DS for a On couple of seconds to switch daylight savings time on or off. The daylight savings (S) symbol switches on or off and the time switches one hour in the appropriate direction. PM Off 2 3 RESET PM 1 4 2 TIME SET Off 1 HOUR MIN DS PROG PROG ON/OFF MODE How to set the clock: a b Introduction Simply plug the DT1 Digital Timer into an electrical outlet (1), then plug your incandescent lights, (PAR lamps), stereo, or appliances (such as an air 1 conditioner) into the DT1 (2). [. . . ] The DT1 is then your programmable timer, random timer, countdown timer and manual switch. Displays 1. Daylight savings symbol PM indicates daylight savings time Auto 2 4 when present. Usually displayed when On light is lit and timer is on, during programming indicates an on time is being programmed. Off display (Usually AM displayed when On light is off Prg and timer is off, during Auto programming indicates an off 5 6 time is being programmed. ) 5. See Modes, next page, for specific mode displays. 1 3 2 1. Note: If it is daylight savings time, push and hold DS for a couple of seconds so the daylight savings symbol appears. If it is not daylight savings time, push and hold DS for a couple of seconds so the daylight savings symbol is off. Seconds are set to 0 when the TIME SET button is released if either the HOUR or MIN have been set. LOAD MAINTENANCE WARNING DO NOT USE THE TIMER TO TURN OFF POWER FOR MAINTENANCE (repairs, removing broken bulbs, etc. ). ALWAYS TURN POWER OFF AT THE SERVICE PANEL BY REMOVING A FUSE OR CIRCUIT BREAKER BEFORE DOING ANY CIRCUIT REPAIRS. MODE Push and release MODE to change the mode. ­ ­ : ­ ­ display means there is nothing programmed for that Prg number and on / off time. Note: You can push and release ON/OFF to switch between the Prg # on time and the Prg # off time. The light bulb symbol switches on or off but the plugged in light(s) do not. RESET AM Prg Auto PROG ON/OFF TIME SET Battery replacement Batteries retain the program during power outages. Batteries should last 3 years or more if the timer is left plugged in. If the display is dim, weak or unreadable when the timer is unplugged from the outlet replace the batteries. After removing the batteries from the unit, you have a minimum of 15 seconds to insert + new batteries without losing existing program. " ALKALINE CELL L1154 6 4 The DT1 uses two L1154 alkaline batteries. Reprogram the DT1 if needed. FULL ONE YEAR WARRANTY If within one (1) year from date of purchase, this product fails due to a defect in materials or workmanship, Intermatic Incorporated will repair or replace it free of charge. The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping; (b) units which have been subject to unauthorized repair, opened, taken apart; (c) units not used in accordance with directions; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you. [. . . ] The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping; (b) units which have been subject to unauthorized repair, opened, taken apart; (c) units not used in accordance with directions; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. This warranty service is available by either: a) returning the product to the dealer from whom the product was purchased or (b) mailing postage prepaid to the authorized service station listed below. [. . . ]