User manual INTERMATIC 158SS11359

[. . . ] Refer to product label for maximum ratings for various voltages and load types. Multiple timers may be mounted in adjacent junction box slots. No derating is required for multiple timers. Note:THE REMOTE SWITCH(ES) MAY NOT FUNCTION RELIABLY WHEN THE ACCUMULATED WIRE LENGTH TO THE REMOTE SWITCH(ES) EXCEEDS 30 FEET OR IF THE WIRING TO THE REMOTE SWITCH(ES) IS BURIED UNDERGROUND. Note: Used remote switches from a previous conventional installation may not function reliably with an electronic timer. Try a brand new remote switch if function is intermittent. MODE ON/OFF EVENT RESET To remove battery: 4. [. . . ] Connect the supplied jumper wire from the common terminal to one of the other two terminals of the switch. (If the light does not turn on when you get to step 9, turn power off at the fuse or circuit breaker and switch the jumper wire to the other terminal. ) DAY H+ M+ DAY Function depends on the mode: CLK mode - Push and release to cycle through the days of the week: MO, TU, WE, TH, FR, SA, SU. PGM mode - Push and release to cycle through all week, weekdays, weekend, individual days of the week and null: MO TU WE TH FR SA SU (all displayed at once is all week) MO TU WE TH FR (all displayed at once is weekdays) SA SU (displayed is weekend) MO, TU, WE, TH, FR, SA, and SU (are individual days) -:-- (on clock display is the null setting) Use null to cancel an unwanted ON or OFF setting. The DAY button does nothing in AUTO, AUTO RAND or MAN modes. Special applications Because of it's unique "hard contact" switch feature, your timer may be used for applications not previously possible for electronic wall timers, such as use with dimmers, use without utility power, use on circuits other than 120 volts, controlling relays or contactors, or to control DC voltage (for example in recreational vehicles). For DC and high voltage applications please note the reduced load ratings on product label. Consult factory for application details. For existing 3 switch installations replace one 3-way switch with the timer and replace the 4-way switch with a 3-way switch. H+ (hour) button MODE ON/OFF EVENT RESET TROUBLESHOOTING GUIDE SYMPTOM Timer does not operate, display is dim, blank or unreadable, display shows nonsense or `lobAt', or timer operates erratically. Timer won't enter the AUTO or AUTO RAND modes when MODE button is pushed. Timer switches at incorrect times or skips some switching times. DAY H+ M+ H+ Works in CLK and PGM modes. If you pass the correct hour, push and hold to cycle around again. POSSIBLE CAUSE Battery is worn out, missing or is installed backwards, or timer was operated while battery was removed. Timer is in AUTO RAND(om) mode (Varies switching times up to +/- 15 minutes). REMEDY Install a fresh AAA size alkaline battery in the direction indicated. Use MODE pushbutton to select AUTO or AUTO RAND Make sure time of day and at least one scheduled activity are programmed. Review / Revise ALL 6 ON/OFF switching time pairs by repeatedly pushing the ON/OFF/EVENT button while in PGM mode. After entering your schedules or the time, then returning to the AUTO modes, push the ON/OFF/EVENT button to change the load state if necessary. Make sure timer display shows `ON' then check dimmer operation at full brightness setting. If timer control is required at very low brightness settings, use a premium quality dimmer that can be turned on when set low. Recheck wiring, especially for the jumper, per "Installation Instructions - 3-Way Switch" and "Other Installations". Eliminate condition, replace the buried cable, do without the remote switch, or consult factory for other options. If the problem persists with the red wire disconnected or with a `remote' switch temporarily connected right at the timer, replace the defective timer, otherwise try the above remedies. [. . . ] The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping; (b) units which have been subject to unauthorized repair, opened, taken apart; (c) units not used in accordance with directions; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. This warranty service is available by either: a) returning the product to the dealer from whom the product was purchased or (b) mailing postage prepaid to the authorized service station listed below. [. . . ]