User manual INTELLINET 520881

[. . . ] Manageable Gigabit Switch Preface This manual describes how to install and use the Manageable Gigabit Switch. This switch introduced here is designed to deliver full scalability with SNMP/RMON web-based management functions by providing: 24 x 10/100BaseTX fixed ports and optional 2 x 1000BaseT/SX/LX ports. 16 x 10/100BaseTX fixed ports and optional 1 x 8-Port 10/100BaseTX/100BaseFX module, 2 x 1000BaseT/SX/LX ports. For the two Gigabit ports, it allows options of fiber type and wavelength at user's discretion. [. . . ] Authentication Failure Trap Step 10: Move to highlight Authentication Failure Trap and press <Enter>. Rising Alarm Trap Step 11: Move to highlight Rising Alarm Trap and press <Enter>. Falling Alarm Trap Step 12: Move to highlight Falling Alarm Trap and press <Enter>. Topology Change Trap Step 13: Move to highlight Topology Change Trap and press <Enter>. Decide to have it Disabled or Enabled. User's Manual 51 Manageable Gigabit Switch Other Protocols Move to highlight [Other Protocols] from [Advanced Management] screen, and press <Enter>. GVRP Step 1: Move to highlight GVRP and press <Enter>. Step 2: Decide to have it Disabled or Enabled. IGMP Step 1: Move to highlight IGMP and press <Enter>. Step 2: Decide to have it Disabled or set in either Passive or Active mode. 52 User's Manual Manageable Gigabit Switch Port Mirroring Move to highlight [Port Mirroring] from [Advanced Management] screen, and press <Enter>. Mirror To Step 1: Press <Enter> to enter Mirror To Options, listing the ports that can be mirrored to. Step 2: Move to highlight the port you want to mirror to and press <Enter>. Mirror From Step 3: Press <Enter> to enter Mirror From Options, listing the ports that can be mirrored from. Step 4: Move to highlight the port you want to mirror from and press <Enter>. From Mode Options, decide whether the port to be mirrored from will be receiving or transmitting. Step 6: Press <Esc> when completed. User's Manual 53 Manageable Gigabit Switch QoS Setup Move to highlight [QoS Setup] from [Advanced Management] screen, and press <Enter>. Global Setting Step 1: Move to highlight Global Setting and press <Enter>. 54 User's Manual Manageable Gigabit Switch Step 2: Move to highlight Diffserv Expedite Forwarding and press <Enter>. Move to highlight to enable or disable Diffserv Expedite Forwarding and press <Enter>. Step 3: Move to highlight ToS/VLAN and press <Enter>. Highlight the desired setting then press <Enter>. Step 4: Move to highlight QoS Status and press <Enter>. Move to highlight to enable or disable QoS Status and press <Enter>. Step 5: Move to highlight WRED Drop Priority Setting and press <Enter>. Move to highlight to Low Drop Percentage or High Drop Percentage and press <Enter>. Step 6: Press <Esc> when completed Logical Port Step 7: Move to highlight Logical Port and press <Enter>. Step 8: Move to highlight User Define Port, Well-Known Port, or Range Port and press <Enter>. Step 9: Move to highlight the appropriate port and press <Enter>. Step 10: Press <Esc> when completed User's Manual 55 Manageable Gigabit Switch VLAN Step 11: Move to highlight VLAN and press <Enter> to specify the QoS VLAN priority. Step 12: Move to highlight Drop Priority or Transmit Priority and press <Enter>. Step 13: Press <Esc> when completed 56 User's Manual Manageable Gigabit Switch ToS Step 14: Move to highlight TOS and press <Enter> to specify the ToS priority. Step 15: Move to highlight Drop Priority or Transmit Priority and press <Enter>. Step 16: Press <Esc> when completed Profile Step 17: Move to highlight Profile and press <Enter> to select a QoS profile. Step 18: Move to highlight Megabit Profile or Gigabit Profile and press <Enter>. Step 19: Press <Esc> when completed User's Manual 57 Manageable Gigabit Switch Port Configuration Step 20: Move to highlight Port Configuration and press <Enter> to specify the port configuration parameters. Step 21: Move to highlight Active Profile, Fixed Drop Priority, or Fixed Transmit Priority and press <Enter>. Step 22: Press <Esc> when completed 58 User's Manual Manageable Gigabit Switch Rate Control Step 23: Move to highlight Rate Control and press <Enter> to specify rate control parameters. Step 24: Move to highlight Rate Control, or Port Number and press <Enter>. Step 25: Press <Esc> when completed. Sending and Receiving Files Move to highlight [File Transfer] from [Advanced Management] screen, and press <Enter>. If you access the administration console by connecting an RS232 cable directly to the console port at the back of the switch, you will see a [File Transfer] screen. RECEIVE FILE VIA TFTP Step 1: Move to highlight Receive File Via TFTP and press <Enter>. Step 2: Type the name of the file you intend to receive and press <Enter>. Step 3: Move to highlight IP Address and press <Enter>. Type the IP address from where the file will be obtained. User's Manual 59 Manageable Gigabit Switch Step 4: Press <Esc> when completed. Step 5: A dialog box appears to ask if you want to transfer file now. Highlight [Yes] and press <Enter> to start file transfer. Otherwise, move to highlight [No] and press <Enter> to deny it. Step 6: Press <Esc> to a previous screen. SEND FILE VIA TFTP Step 1: In [File Transfer] screen, move to highlight Send File Via TFTP and press <Enter>. Step 2: If the default File Type is not the one you intend to send, press <Enter>. Select the file type you intend to send and press <Enter>. Step 3: Repeat Step 3-5. RECEIVE FILE VIA KERMIT Step 1: In [File Transfer] screen obtained via console port, move to highlight Receive File Via Kermit and press <Enter>. Step 2: A dialog box appears to ask if you want to transfer file now. Move to highlight [Yes] and press <Enter> to start file transfer. Otherwise, highlight [No] and press <Enter> to deny it. Step 3: Press <Esc> to a previous screen. SEND FILE VIA KERMIT Step 1: In [File Transfer] screen obtained via console port, move to highlight Send File Via Kermit and press <Enter>. Step 2: Move to highlight a file type you intend to send and press <Enter>. Step 3: A dialog box appears to ask if you want to transfer file now. Move to highlight [Yes] and press <Enter> to start file transfer. Otherwise, highlight [No] and press <Enter> to deny it. Step 4: Press <Esc> to a previous screen. 60 User's Manual Manageable Gigabit Switch Logout To log out, highlight [Logout] from [Switch Management] screen and press <Enter>. [. . . ] RMONs typically consist of two components: an RMON probe and a management workstation: - The RMON probe is an intelligent device or software agent that continually collects statistics about a LAN segment or VLAN. The RMON probe transfers the collected data to a management workstation on request or when a pre-defined threshold is reached. - The management workstation collects the statistics that the RMON probe gathers. The workstation can reside on the same network as the probe, or it can have an in-band or out-of-band connection to the probe. The switch provides RMON capabilities that allow network administrators to set parameters and view statistical counters defined in MIB-II, Bridge MIB, and RMON MIB. [. . . ]