User manual INDESIT VRM 640 C

[. . . ] WE ADVISE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE HOB. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. [. . . ] The illicit disposal of the product by the user results in the application of administrative sanctions. The product does not contain substances in quantities sufficient to be considered hazardous to health and the environment, in accordance with current European directives. 3. 2 Your environmental care Our product's packaging is made of non-polluting materials, therefore compatible with the environment and recyclable. You can obtain the addresses of collection, recycling and disposal centres from your retailer or from the competent local organisations. Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. Important: hand over your appliance to the local agency authorised for the collection of household appliances no longer in use. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power grid, removing it along with the plug. 8 Instructions for the user 4. DESCRIPTION OF CONTROLS 4. 1 Control zone All the hob controls are grouped together on the front panel. CONTROL ZONE 4-burner hob 5-burner hob KNOB DESCRIPTION To light the flame, press the knob and turn it anticlockwise to between the maximum minimum flame symbol and the . To adjust the flame, turn and the knob to the area between the maximum minimum settings knob to position . . Do not use aggressive products containing alcohol or products for cleaning steel and glass when cleaning the knobs, as these products could cause permanent damage. 14 Instructions for the user 6. 2. 2 Pan stands Remove the pan stands and clean them with lukewarm water and non-abrasive detergent, making sure to remove any encrustations. After having fastened the hob to the unit (See "7. 3 Fixing using brackets"), carefully trim the surplus away from edge C beyond the seal. The dimensions given in the following drawing refer from the hole to the inside of the seal. 17 Instructions for the installer 7. 3 Fixing using brackets The figure to the side shows the exact holes to be used to correctly attach the hob to the counter top with brackets. Fix the hob to the unit using the appropriate brackets supplied. To secure the hob correctly to the counter top, tighten the brackets A in the appropriate holes on the sides of the casing. Take care while securing with the brackets; if tightened too much the glass may be strained causing it to crack. 18 Instructions for the installer 8. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. Pass the power supply cable through the back of the unit, taking care that it does not touch the bottom casing of the hob or the oven (if any) installed underneath it. Fit the power supply line with a multipolar cut-out device with a contact opening gap equal to or greater than 3 mm in an easily accessible position close to the appliance. Avoid use of adapters and shunts. If the power cable is replaced, the crosssection of wires in the new cable must be no less than 1 mm2 (3 x 1 mm² cable), remembering that the end to connect to the appliance must have an earth wire (yellow/ green) which is at least 20 mm longer. Only use a H05V2V2-F type cable or similar resistant to a maximum temperature of 90°C. The cable must be replaced by a specialised technician who must carry out the connection to the power grid following the diagram below. L = brown N = blue = yellow/green The power supply cable must be replaced by an authorised service centre to prevent any risks. [. . . ] Using a a double head, remove nozzle C and replace it with the appropriate nozzle, following the instructions in the tables for the type of gas to be used. Move the Venturi tube D to adjust the air flow until distance "X" is reached as indicated in the table in paragraph "10. 4 Primary air adjustment" and then secure the tube by means of screw A. After the adjustments have been carried out, restore the seals with sealing wax or equivalent material. Burner Rated heating capacity (kW) Nozzle diameter 1/100 mm LPG ­ G30/G31 28/37 mbar Reduced capacity (W) 400 500 1000 750 1600 400 1400 Capacity g/h G30 80 124 225 189 256 73 233 Capacity g/h G31 79 121 221 186 250 71 229 Auxiliary (1) Semi-rapid (2) Rapid (3) Reduced Rapid (4) Ultra-rapid (5) Double crown Internal (6) External (6) 1. 1 1. 7 3. 1 2. 6 3. 5 1. 0 3. 2 48 62 85 76 87 48 85 23 Instructions for the installer 10. 3 Adjustment for natural gas The hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. To reset the appliance for operation with this type of gas, carry out the same steps as described in "10. 2 Adjustment for LPG", but select the nozzles and adjust the primary air for natural gas as indicated in the table below and in "10. 4 Primary air adjustment". [. . . ]