User manual IIYAMA PROLITE T1932MSC

[. . . ] USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. ENGLISH CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC Directive 2004/108/EC “EMC Directive” , 2006/95/EC “Low Voltage Directive” and 2009/125/EC “ErP Directive”. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. [. . . ]  You are able to adjust the monitor ’s angle up to 90 degrees upward, 5 degrees downward.  Careful attention is required not to catch your fingers or hands when you change the angle. 90° 5° 8 BEFORE YOU OPERATE THE MONITOR OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 24. You are also able to adjust the picture by following the button operation shown below. There are additional Menu items which can be switched by using the / Buttons. CO NTRAS T BRIG HTNE S S 1280x1024 FH: 63KHz F V: 5 9 . 9 H z B Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. D Press the Button to leave the menu, and the settings you just made would be automatically saved. The vertical position of the overall display should be changing accordingly while you are doing this. Press the Button lastly, it ends, any changes are saved in the memory. AUTO ADJUST H-POSITION V-POSITION H-SIZE FINE 100 NOTE When button operations are aborted during adjustment, On-Screen Display disappears when the  time set for the OSD TIMEOUT has passed.  Any changes are automatically saved in the memory when the On Screen Display disappears. Adjustments for H/V-POSITION, H-SIZE and FINE are saved for each signal timing. Except for these  adjustments, all other adjustments have only one setting which applies to all signal timings. OPERATING THE MONITOR 9 ENGLISH ADJUSTMENT MENU CONTENTS CO NTRAS T BRIG HTNE S S ENGLISH 1280x1024 FH: 63KHz F V: 5 9 . 9 H z Adjustment Item Problem / Option Too dull Too intense Too dark Too bright Button to Press CONTRAST BRIGHTNESS * Direct * Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations. BRIGHTNESS: Press the  Button when the Menu is not displayed. Direct LOCK MODE:  Press the button to display the OSD menu. The following OSD menu is displayed. Adjustment Item POWER OSD LOCK UNLOCK LOCK UNLOCK Problem / Option The POWER SWITCH is Locked. The OSD menu is Unlocked. TOUCH FANCTION DISABLE:  ON: Pressing and holding of the Button and the Button at the same time when the Menu is not displayed, massage "TOUCH DISABLE" will appear on the top right corner. OFF: Pressing and holding of the Button and the Button at the same time for about 5 seconds when the Menu is not displayed, till "TOUCH DISABLE" disappears. 10 OPERATING THE MONITOR Only Analog Input AUTO ADJUST H-POSITION V-POSITION H-SIZE FINE Adjustment Item AUTO ADJUST *1 Problem / Option Button to Press Direct Adjust H/V-POSITION, H-SIZE and FINE automatically. H-POSITION Too left Too right Too low Too high Too narrow Too wide V-POSITION H-SIZE *2 FINE *2 To correct flickering text or lines *1 For best results, use the Auto Adjust in conjunction with the adjustment pattern. *2 See page 14 for SCREEN ADJUSTMENTS. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations. AUTO ADJUST: Press the  Button when the Menu is not displayed. OPERATING THE MONITOR 11 ENGLISH OS D H - P OS I TI ON OS D V- P OS I TI ON OS D TI ME OU T RESET I N P U T S E LE C T Adjustment Item Problem / Option OSD is too left OSD is too right OSD is too low OSD is too high You can set the OSD display duration time between 5 and 60 seconds. Button to Press ENGLISH OSD H-POSITION OSD V-POSITION OSD TIMEOUT RESET Factory-preset data is restored. Select the digital input. INPUT SELECT NOTE When only one of the two signal inputs is connected to the signal source, the one connected is automatically selected. Input Select function is not available if there is no signal input from the selected connector or during the power management mode. ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL Adjustment Item Problem / Option ENGLISH FRANÇAIS DEUTSCH ITALIANO English French German Italian ESPAÑOL Button to Press Spanish Japanese Traditional Chinese Simplified Chinese OSD LANGUAGE 12 OPERATING THE MONITOR 9300 6500 5500 7500 USER RED GREEN BLUE 94 90 100 Adjustment Item Problem / Option 9300 6500 5500 Bluish white Reddish white Greenish white Yellowish white RED Too weak GREEN Too strong BLUE Button to Press COLOR TEMP. 7500 USER VOLUME MUTE Adjustment Item Problem / Option Too soft Too loud ON Turn off the sound temporarily. Button to Press VOLUME MUTE Direct OFF Return the sound volume to the previous level. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations.  : MUTE ON : MUTE OFF OPERATING THE MONITOR 13 ENGLISH SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input.  The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. [. . . ] Check your operating system manual for information on how this can be configured. When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor enters into Power Management Mode which reduces the power consumption to less than 2W. From Power Management Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again. NORMAL MODE POWER MANAGEMENT MODE POWER 0 2W CONSUMPTION 100% NOTE Even when using the power management mode, the monitor consumes electricity. Turn off  the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption. It is possible that the video signal from the computer may be on while the H or V sync  signal is missing. [. . . ]