User manual IIYAMA PROLITE T1532SR

[. . . ] USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. ENGLISH CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" , 2006/95/EC "Low Voltage Directive" and 2009/125/EC "ErP Directive". The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. [. . . ] Power Cable* RS-232C Cable Screw (M3x6mm) Safety Guide CAUTION 1 D-Sub Signal Cable DVI-D Cable USB Cable Audio Cable Touch Panel Driver Disk (CD-ROM)*2 Quick Start Guide *2 This CD-ROM contains the touch screen driver software. Connect the computer to the monitor with the RS-232C Cable or the USB Cable. Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features. Connect the Power Cable to the monitor first and then to the power supply. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office. For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor. NOTE The signal cables used for connecting the computer and monitor may vary with the type of Make sure you tighten the finger screws at each end of the Signal Cable and the RS232C Cable. Don't connect the RS-232C cable and the USB cable to the computer at the same time. [Example of Connection] Power Cable (Accessory) USB Cable (Accessory) RS-232C Cable (Accessory) Audio Cable (Accessory) D-Sub Signal Cable (Accessory) DVI-D Signal Cable (Accessory) Computer [Collect Cables] Put the cables through the cable holder and holes. Collect cables at the back of the stand. Cable Holder Cable Holes BEFORE YOU OPERATE THE MONITOR 7 ENGLISH COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 28: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista/7 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. For installation on Windows 95/98/2000/Me/XP: The monitor Information File for iiyama monitors ENGLISH may be necessary for your computer and obtained via the Internet, using the address: http://www. iiyama. com NOTE For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above. Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer first for advice. Procedure for turning ON the Power Switch Turn ON the monitor first, and then the computer. Touch screen driver software Touch screen driver software and system may not start when you start your computer while touching the screen. Touch screen driver software may not run due to the power saving function depending on the BIOS of your computer. In this case, set the power saving function to off. ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor. Hold the panel so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor 's angle up to 90 degrees upward, 5 degrees downward. [. . . ] To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be configured. enters into Power Management Mode which reduces the power consumption to less than 2W or 3W. * The screen becomes dark. [. . . ]