User manual IIYAMA PROLITE C1911S

[. . . ] USER MANUAL ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. POLSKI ENGLISH TABLE OF CONTENTS FOR YOUR SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CABINET LCD SCREEN 3 Stains can be removed with a cloth lightly moistened with a mild detergent solvent. because these will damage the LCD screen. FOR YOUR SAFETY BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1280 × 1024 High Contrast 1000:1 (Typical) / Brightness 300cd/m2 (Typical), Quick Response Time 5ms (Gray to Gray) Digital Character Smoothing Automatic Set-up Stereo Speakers 2 × 1W Stereo Speakers Plug & Play VESA DDC2B Compliant Windows® 95/98/2000/Me/XP/Vista Compliant VESA Mounting Standard (100mm×100mm) Compliant Keyhole for Security Lock ENGLISH RCA-BNC Adapter BEFORE YOU OPERATE THE MONITOR 4 CHEKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office. Power Cable* Stand CAUTION D-Sub Signal Cable Quick Start Guide * The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using a power supply higher than this rating, then a power cable with a rating of 10A/ 250V must be used. However, all guarantees and warranties are void for any problems or damage caused by a power cable not supplied by iiyama. FITTING AND REMOVAL OF BASE CAUTION Install the stand on a stable surface. Unplug the monitor before installation to avoid electric shock or damage. <Installation> ENGLISH Lay the monitor flat on a table with LCD screen face down. To prevent the monitor from being scratched, put a piece of soft cloth on the table on which the screen will be set. Unpack the stand and mount it onto the monitor base, aligning the base with the hook for the base. Slide the stand upward until you hear a click, which indicates that the stand is attached and installed. <Remove> Lay the monitor flat on a table with LCD screen face down. To prevent the monitor from being scratched, put a piece of soft cloth on the table on which the screen will be set. Hold the monitor and stand with both hands, and then slowly push the hook up, do not loose. Hold the monitor firmly with one hand and slide the stand downward with the other hand. Make sure you slide the stand down slowly or you may damage both the monitor and the stand. NOTE Please refer to label on back of stands base. 5 BEFORE YOU OPERATE THE MONITOR CONTROLS AND CONNECTORS <Front> <Back> Power Switch ( Power Indicator ) Power is ON. For installation on Windows 95/98/2000/Me/XP: The monitor Information File for iiyama monitors http://www. iiyama. com NOTE For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above. Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer first for advice. ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor. Hold the stand so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor's angle up to 20° upward, 5° downward. In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, it is recommended that the adjusted tilt angle should not exceed 10 degrees. Careful attention is required not to catch your fingers or hands when you change the angle. Do not tilt the post beyond 20 degrees except when repacking the monitor in its box. To do so may cause the monitor to fall over and break. BEFORE YOU OPERATE THE MONITOR 8 ENGLISH may be necessary for your computer and obtained via the Internet, using the address: OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 19. [. . . ] 95/98 cancel the setting of "Stretch desktop wallpaper to fit the screen". [Adjustment pattern] Color bar Zebra pattern Picture frame OPERATING THE MONITOR 14 ENGLISH Auto Adjust. Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust. Adjust the V-Position so that the top and bottom of the picture frame will fit to the display area. ENGLISH 1) Adjust the H-Position so that the left side of the picture frame will move to the left edge of the display area. 2) Stretch the right side of the picture frame to the right edge of the display area by adjusting the Clock. NOTE NOTE When the left side of the picture frame moves apart from the left edge of the display area during the Clock adjustment, adjust steps 1) and 2). Another way to make the Clock adjustment is to correct the vertical wavy lines in the zebra pattern. [. . . ]