User manual IIYAMA E2410HDS

[. . . ] USER MANUAL ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. POLSKI ENGLISH This display carries the TCO Certified label. This ensures that the display is designed for minimal impact on the climate and natural environment, while offering all the performance expected from top of the line electronic products. [. . . ] An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office. For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor. ENGLISH Make sure you tighten the finger screws at each end of the signal cable. [Example of Connection] <Back> Power Cable (Accessory) Audio Cable (Accessory) D-Sub Signal Cable (Accessory) DVI-D Cable (Accessory) HDMI Cable (Not Included) Computer AV Equipment * Available for ProLite E2410HDS only. 7 BEFORE YOU OPERATE THE MONITOR COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 24: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista/7 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. For installation on Windows 95/98/2000/Me/XP: The monitor Information File for iiyama monitors http://www. iiyama. com NOTE For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above. Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer first for advice. ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor. Hold the stand so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor 's angle up to 20 degrees upward, 5 degrees downward. In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, it is recommended that the adjusted tilt angle should not exceed 10 degrees. Careful attention is required not to catch your fingers or hands when you change the angle. 5 20 BEFORE YOU OPERATE THE MONITOR 8 ENGLISH may be necessary for your computer and obtained via the Internet, using the address: OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 24. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 16 for SCREEN ADJUSTMENTS. Press the MENU Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the + / - Buttons. Luminance Contrast Brightness 50 50 Off Standard ON ENGLISH Eco Picture Mode ACR B Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. D Press the AUTO Button to leave the menu, and the settings you just made would be automatically saved. For example, to correct for vertical position, select Menu item of Image Setup and then press the MENU Button. The vertical position of the overall display should be changing accordingly while you are doing this. Press the AUTO Button lastly, it ends, any changes are saved in the memory. Image Setup Clock Phase H. Position V. Position Aspect Full 50 50 50 50 NOTE When button operations are aborted during adjustment, On-Screen Display disappears when the time set for the Timeout has passed. Also, the AUTO button can be used to return previous menu and turn off the On-Screen Display. Any changes are automatically saved in the memory when the On Screen Display disappears. [. . . ] The power management function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be configured. ENGLISH Power Management Mode When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor enters into Power Management Mode which reduces the power consumption to less than 1W. From Power Management Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again. Power Indicator NORMAL MODE POWER MANAGEMENT MODE Blue Orange POWER 0 1W CONSUMPTION 100% NOTE Even when using the power management mode, the monitor consumes electricity. Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption. [. . . ]