User manual IIYAMA E2202WSV

[. . . ] USER MANUAL ENGLISH ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. [. . . ] (See page 32 for CONNECTOR PIN ASSIGNMENT. ) C Connect the monitor to the audio equipment with the Audio Cable when using the audio features. D Connect the Power Cable to the monitor first and then to the power supply. NOTE The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office. For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor. Make sure you tighten the finger screws at each end of the signal cable. [Example of Connection] <Back> ENGLISH Power Cable (Accessory) D-Sub Signal Cable (Accessory) DVI-D Signal Cable* Audio Cable (Accessory) * Available for ProLite E2202WS only. Computer [ Fitting of Cable Holder ] A Collect cables at the back of the stand. B Position the Cable Holder at the base of the stand column by inserting the `tabs' into the guide holes. Apply gentle pressure downwards to secure. Stand [ Removal of Cable Holder ] A Remove Cable Holder by sliding up the base column. 10 BEFORE YOU OPERATE THE MONITOR COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 31: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. Windows 95/98/2000/Me/XP/Vista Monitor Information File for iiyama monitors may be necessary for your computer and obtained via the Internet, using the address: http://www. iiyama. com NOTE For additional information on how to download the driver for your monitor, please access one of the internet sites noted above. Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer first for advice. ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor. Hold the stand so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor's angle up to 20 degrees upward, 5 degrees downward. In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, it is recommended that the adjusted tilt angle should not exceed 10 degrees. Careful attention is required not to catch your fingers or hands when you change the angle. 20 5 BEFORE YOU OPERATE THE MONITOR 11 ENGLISH OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 31. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 21 for SCREEN ADJUSTMENTS. ( Press the Menu Button to start the On Screen Display feature. [. . . ] Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption. It is possible that the video signal from the computer may be on while the H or V sync signal is missing. In this instance, the POWER MANAGEMENT feature may not work properly. 24 OPERATING THE MONITOR TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. [. . . ]