User manual IIYAMA PROLITE B2280HS

[. . . ] Visual ergonomics for good image quality is tested to ensure top performance and reduce sight and strain problems. Important parameters are luminance, contrast, resolution, black level, gamma curve, colour and luminance uniformity and colour rendering · Products are tested according to rigorous safety standards at impartial laboratories · electric and magnetic fields emissions as low as normal household background levels · Low acoustic noise emissions (When applicable) Very low energy consumption both in on- and standby mode minimize climate impact · Restrictions on chlorinated and brominated flame retardants, plasticizers, plastics and heavy metals such as cadmium, mercury and lead (RoHS compliance) · Both product and product packaging is prepared for recycling · The brand owner offers take-back options The requirements can be downloaded from our web site. The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. [. . . ] <Stopper pin> Please stand the monitor and then remove the stopper pin on the back of the stand slowly while pushing top face of the stand before you install the monitor. Careful attention is required as the monitor is sprung loaded and may expand quickly when removing it. A Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. C Fix the Monitor to the Stand by both screws firmly and then push-down knob. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Hold the monitor and push the Stand-Base until it clicks and is secure. <Removal> Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. There are two locks inside of the Stand, unlock them by thin stick and pull the Stand away from the monitor. D-SUB mini 15pin Connector (D-SUB) DVI-D 24pin Connector (DVI) HDMI Connector (HDMI) Cable holder AC Connector (AC IN) Keyhole for Security Lock NOTE You can fasten a security lock and cable to prevent the monitor from being removed without your permission. D-SUB mini 15pin Connector (D-SUB) DVI-D 24pin Connector (DVI) HDMI Connector (HDMI) AC Connector (AC IN) Keyhole for Security Lock NOTE You can fasten a security lock and cable to prevent the monitor from being removed without your permission. Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features. In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, it is recommended that the adjusted tilt angle should not exceed 10 degrees. Careful attention is required not to catch your fingers or hands when you change the angle. Do not tilt the post beyond 20 degrees except when repacking the monitor in its box. For optimal viewing it is recommended to position yourself directly opposite to the full face of the monitor, then adjust the monitor's height and angle to your own preference. Hold the panel so that the monitor does not topple when you change the monitor's height or angle. You are able to adjust the monitor's height up to NOTE Do not touch the LCD screen when you change the height or the angle. Careful attention is required not to catch your fingers or hands when you change the height or the angle. Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height. You can skip the Menu items and display an adjustment scale directly by using the following button operations. To correct flickering text or lines Too left Too right Too low Too high Full Aspect Expansion display Expansion display of Aspect Mode1 Mode2 Mode3 Warm Normal Cool Normal High contrast Dark Greenish white Yellowish white Bluish white User-R User-G User-B sRGB Too weak Too strong SRGB is an international standard which defines and unifies the difference of color appearance between equipment. You can not adjust the Brightness, Contrast, Gamma and Eco during sRGB mode because those settings are locked. [. . . ] In case the picture frame is bigger or smaller than the data display area after the Clock adjustment, repeat steps from C. G Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern. In case the strong flicker or blurs remain on a part of the screen, repeat steps F and G because the Clock may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from C again. [. . . ]