User manual IIYAMA PROLITE B2008HDS

[. . . ] USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. AB52 ENGLISH CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" , 2006/95/EC "Low Voltage Directive" and 2009/125/EC "ErP Directive". The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. [. . . ] You are able to adjust the monitor's height up to 100mm, angle up to 45 degrees right and left, 20 degrees upward, 5° downward. 5° 20° 100mm NOTE Do not touch the LCD screen when you change the height or the angle. Careful attention is required not to catch your fingers or hands when you change the height or the angle. 45° 45° ADJUSTING THE VIEWING ANGLE : ProLite E2008HDS / ProLite E2008HDD For optimal viewing it is recommended to look at the full face of the monitor. Hold the stand so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor's angle up to 20° upward, 5° downward. In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, it is recommended that the adjusted tilt angle should not exceed 10 degrees. Adjust the monitor's angle to your own preference. NOTE Do not touch the LCD screen when you change the angle. Careful attention is required not to catch your fingers or hands when you change the angle. Do not tilt the post beyond 20 degrees except when repacking the monitor in its box. To do so may cause the monitor to fall over and break. BEFORE YOU OPERATE THE MONITOR 11 ENGLISH OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 28. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 18 for SCREEN ADJUSTMENTS. Press the ENTER Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the / Buttons. Main Menu Auto Adjust Luminance Language Recall Miscellaneous Input Select Audio ENGLISH Geometry Color OSD Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. / Buttons to make the appropriate Press the EXIT Button to leave the menu, and the settings you just made would be automatically saved. For example, to correct for vertical position, select Menu item of Geometry and then press the ENTER Button. Then, select (V. Position) by using the / Buttons. Main Menu Auto Adjust Luminance Geometry Color OSD Language Recall Geometry H. Position Miscellaneous Input Select Audio 50 50 50 50 Pixel Clock Phase An adjustment page appears after you press the ENTER Button. The vertical position of the overall display should be changing accordingly while you are doing this. Press the EXIT Button lastly, it ends, any changes are saved in the memory. Geometry V. Position 50 NOTE When button operations are aborted during adjustment, On-Screen Display disappears when the time set for the OSD Time has passed. Also, press the EXIT button to quickly turn off the On-Screen Display. Any changes are automatically saved in the memory when the On Screen Display disappears. Except for these adjustments, all other adjustments have only one setting which applies to all signal timings. 12 OPERATING THE MONITOR ADJUSTMENT MENU CONTENTS Auto Adjust Adjustment Item Auto Adjust * Only Analog Input Problem / Option Button to Press Direct Adjust H. Position, Pixel Clock and Phase automatically. * For best results, use the Auto Adjust in conjunction with the adjustment pattern. [. . . ] There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be configured. Power Management Mode When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor enters into Power Management Mode which reduces the power consumption to less than 1W. From Power Management Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again. Power Indicator NORMAL MODE POWER MANAGEMENT MODE Blue Orange POWER 0 1W CONSUMPTION 100% NOTE Even when using the power management mode, the monitor consumes electricity. [. . . ]