User manual IDEAL ND2356

[. . . ] Even if the LED can't be seen, or the beeper can't be heard the shake can be felt. NCV Non-contact voltage indicator Continuity indicator CP Clean power indicator (#61-702) 6. Max button Press Max prior to a measurement to capture the maximum reading displayed during the measurement. To clear the max value, press the max button again, or press the reset button (#61-700). [. . . ] Keep your body isolated from ground by using dry clothing, rubber shoes, mats, or any other approved insulating material. Before beginning all unknown measurements, set meter to highest possible range. Disconnect the meter from the circuit before turning off any inductor, including motors, transformers, and solenoids. General Operation Lead Storage Silicone test leads are provided with the meter. These test leads stay flexible in very cold weather and can withstand high temperatures without melting. For convenient lead storage, wrap the leads as shown. AC Current Auto power off To extend the life of your battery, the meter automatically turns off after approximately 60 minutes. Selecting Ranges For all ranges and functions choose a range just above the expected value. If display shows less than three numbers, select a lower range for better resolution. Accuracy Specifications Accuracy specifications are based on nominal operating temperature of 74°F ±8°, and a relative humidity less than 75%. Accuracy is specified as ± (% of reading + number of least significant digits). Range Resolution Max Accuracy Models Display 200A 0. 1A 199. 9 ±(3%+5) 61-700, 61-701, 61-702 Frequency response: 50Hz - 60Hz; ±(5%+5) 60Hz - 400Hz. With the jaws closed, separate one wire from a bundle using the long fixed jaw. Slide the wire to the corner where the two jaws meet, then open the jaws to let it in. AC & DC Volts DC Voltage Range Resolution 200mV 2000mV 20V 200V 600V 1000V 0. 1mV 1mV 10mV 0. 1V 1V 1V Max Display 199. 9 1999 19. 99 199. 9 600 1000 Accuracy Models ±(0. 5%+1) 61-700 ±(0. 5%+1) 61-700, 61-702 ±(0. 5%+1) 61-701 ±(0. 5%+1) 61-700, 61-702 ±(0. 5%+1) 61-700 ±(0. 5%+1) 61-702 To Measure Voltage: 5. Plug the black test lead into the COM port and the red test lead into the + port. Measure the voltage Frequency Max Accuracy Models Display 2000mV 1mV 1999 ±(1. 2%+3) 61-702 200V 0. 1V 199. 9 ±(1. 2%+3) 61-700, 61-701, 61-702 600V 1V 600 ±(2%+5) 61-700, 61-701 750V 1V 750 ±(2%+5) 61-702 Frequency response: 50Hz - 500Hz; ±(2%+5) 500Hz - 1KHz; 50Hz - 500Hz on 600V and 750V ranges. AC Voltage Range Resolution Range 2k~40kHz Resolution 1Hz Max Accuracy Display 40. 0 ±(0. 1%+3) Model 61-700, 61-701 7 8 Capacitance Testing To Measure Frequency: 1. Plug the black test lead into the COM port and the red test lead into the + port. Resistance (Ohms) Range 200MFD Resolution 0. 1MFD Max Accuracy Models Display 199. 9 ±(3% +5) 61-701, 61-702 Range 200 200k Resolution 0. 1 0. 1k Max Display 200. 0 200. 0 Accuracy ±(1% +3) ±(1% +3) To Measure Capacitance: 1. Disconnect any resistors that might be between the terminals of the capacitor. Plug the black test lead into the COM port and the red test lead into the + port. Diode Check: To ensure a proper functioning diode, the meter will develop a voltage across the component from a test current. The diode test function allows measurements of forward voltage drops across diode and transistor junctions. [. . . ] Lifetime Limited Warranty This meter is warranted to the original purchaser against defects in material or workmanship for the lifetime of the meter. will, at its option, replace or repair the defective unit, subject to verification of the defect or malfunction. This warranty does not apply to defects resulting from abuse, neglect, accident, unauthorized repair, alteration, or unreasonable use of the instrument. Any implied warranties arising out of the sale of an IDEAL product, including but not limited to implied warranties of merchantability and fitness for a particular purpose, are limited to the above. [. . . ]