User manual ICOM RS-RP2C

[. . . ] 3­11 I Gateway server connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 I Router settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 D IP address setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 D Port forwarding setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] c Click x Select x Click to add ". " z Click z Click w Click "DNS name Server" to add a check mark, ", " and then click "Details. " c Click r Click [Update] to start the installation. Click to add ". " Click Click 2 SYSTEM SETUP I Gateway server connections D Connecting to the ID-RP1 system ID-RP1D (Zone repeater) Gateway server 2 to Internet Modem LAN card: eth0 LAN card: eth1 to [ 10B AS E-T ] Router to eth0 to eth1 Coupler D Connecting to the ID-RP2 system ID-RP2 (Zone repeater) Gateway server to Internet Modem LAN card: eth0 LAN card: eth1 Router to eth0 to eth1 to [10BASE-T] 3 2 SYSTEM SETUP I Router settings D IP address setting Set the specified IP addresses for both WAN and LAN as follows. IP address (WAN) : Enter the fixed global IP address that is specified from the ISP. IP address (LAN) : 10. 0. 0. 1 NOTE: The same IP address (for LAN; 10. 0. 0. 1) is used for all gateways. NEVER use other private IP address. D Port forwarding setting Set the following port number with protocol to transferring to the IP address "10. 0. 0. 2. " Port No. /Protocol 20005/TCP Usage IP server synchronization File location PORT_SYNC (/etc/dsipsvd. conf) GW_VCPORT (/etc/dsgwd. conf) GW_DTPORT (/etc/dsgwd. conf) 40000/UDP Voice transfer 40001/TCP Data transfer NOTE: IP filter must be set to allowing Internet remote access to local IP address "10. 0. 0. 2. " Otherwise the D-STAR gateway will not work due to the firewall. I Sever settings D LAN card settings q Open "Network Configuration" screen with the following mouse operation. x Select NOTE: The fixed value for both the IP address and subnet mask must be set to both eth0 and eth1. Otherwise the gateway server cannot communicate to another D-STAR gateway. e Select [Statically set IP address], then enter the specified IP address, subnet mask and default gateway (router side; eth0 setting only), as below. Click [OK], then close "Ethernet Device" screen. Displays the LAN card name that is selected in steps w. c Click eth0: 255. 0. 0. 0 eth1: 255. 255. 255. 0 eth0: 10. 0. 0. 2 eth1 172. 16. 0. 20 z Click Select w Select [eth0] or [eth1] to select router or repeater side respectively, then click [Edit]. · The "Ethernet Device" screen appears as right above. Click eth0: 10. 0. 0. 1 eth1: Blank Click r Click [DNS] tub in "Network Configuration" screen, then enter the address "127. 0. 0. 1" (fixed value) into "Primary DNS" column. For router For repeater Click Primary DNS: 127. 0. 0. 1 4 SYSTEM SETUP 2 D Named setting IMPORTANT!: Master the basis of BIND with a reference book of Linux, before starting the named setting. q Add local zone setting file (dstar. local. ) to "/etc/named. conf. " · e. g. ; /etc/named. conf v Click c Select x Select e Open "Service Configuration" screen with the following mouse operation. Add z Click r Click the check box beside "named, " then save the changed setting if no check mark, ", " is added. w Create database, /var/named/dstar. local. db, for local D-STAR as the following example. NOTE: A full-stop period must be applied into 2nd, 3rd and 10th lines. ;##DSTAR A RECORD · e. g. ; /var/named/dstar. local. db x Click c Click to save z Click to add check mark, ". " Full stop period Full stop period t Select "named" item, then click [Restart] to restart the named setting. x Click Full stop period z Select Separator For your information When "Fedora Core 2" is used, the database location is "/var/named/chroot/var/named/dstar. local. db. " 5 2 SYSTEM SETUP D DNS function verification q Start up "Terminal" with the following mouse operation. e When the correct router IP address "10. 0. 0. 1" is displayed in the answer section as below, the GW setup is succeeded. x Select Enter the command z Click c Click Router IP address w The local DNS operation can be verified by entering the following command. # dig router. dstar. local I Gateway control software D Installation q Insert the RS-RP2C CD into the drive. w Expands the file into the "/dstar" directory using with the following command, or double-click the file during the CD content is displayed. Command: # tar zxvf dstar-xxxx. tar. gz (XXXX=revision number) e Copy the both "dsgwd. conf" and "dsipsvd. conf" files, expanded in the "/dstar/conf" directory, into the "/etc" directory. r Open the copied files, then edit the contents to suits the network. · See page 8 and 9 for details. D Syslog setting For your convenience: Set the syslog if desired. By setting the syslog, easy log management is provided because of the independent log. Add the following contents in "etc/syslog. conf. " # for D-STAR local0. * /var/log/dsgwd. log local2. * /var/log/dsipsvd. log D Starting up the control software Execute script "/dstar/exec-mgsv" when starting up the gateway control software. When starting up the control software and the system at the same time, add the command as above in the "/etc/rc. d/rc. local. " And we recommend to set the server condition as described at right above to improve the gateway server performance. · Deactivate all the services except below anacron, apmd, atd, crond, keytable, named, network, ntpd, random, sshd, syslog, xinetd · Do not start up the X-Window System when starting up the gateway server Change the "Default runlevel" in "/etc/inittab" from 5 to 3. *The X-Window System start up manually with the "startx" command. 6 SYSTEM SETUP 2 D Data base directory Make the directory for data base backup in the "/var. " "/var/dsipsvd" is specified as the default setting. · Refer to y BACKUPDIR_PATH (p. The application timer is the waiting timer (unit: second) until the connection is succeeded when making a new connection to another gateway in data mode operation. [. . . ] #echo "del ID1000"> /tmp/dsipsvdcmdin Format: delY[CS(T)] Y NOTE: A delete flag is applied to the deleted station data in the MNG. (The record is not deleted, the delete flag "1" is added only. ) The deleted call sign is usable when "add" command is used. D Backup file A backup file is made with the following file name and contents into the directory that is specified in "BACKUPDIR_PATH" in IP server's parameter. · Global IP address table (gip_YYYYMMDD_HHmmss_uuuuuu. dat) File contents: [GWIP][tab]Registered time[tab]Communication permission[tab]Effective flag · Target information table (mng_YYYYMMDD_HHmmss_uuuuuu. dat) File contents: [GWIP][tab][CS(Z)][CS(A)][tab][CS(T)][tab] [HNAME][tab][TIP][tab]Registered time[tab]Delete flag[tab]CommandExec. Time (YYYY: Year), (MM: Month), (DD: Day), (HH: Hour), (mm: Minutes), (ss: Second), (uuuuuu: micro second) · Reserved IP address table (rip_YYYYMMDD_HHmmss_uuuuuu. dat) File contents: [Reserved head IP address][tab][GWIP][tab]Registered time[tab]Effective flag D Data base maintenance The maintained data will be restored when the gateway server synchronized with another gateway even if the data has been deleted because of the IP servers are synchronized each other. q Read out the "TRUST SERVER" data with the "write" command. · Used the same format for the file name as the "Backup file" as described above. w Deactivate the all programs that are connected to the gateway server. [. . . ]