User manual ICOM MR-570R

[. . . ] MR-570R s Display information Tuning level indicator Screen range readout Fixed ring range readout*1 OPERATING GUIDE Heading indicator 3 (1) NM 2530° T TM Mode indicator*5 Cross line cursor Heading line Alarm zone*2 EBL1/2 Own ship vector indicator VRM1/2 Waypoint marker*3 MOB symbol Fixed range rings*1 EBL1/VRM1, EBL2/VRM2 readouts*4 EBL/VRM1 EBL/VRM2 S0672°R S0162°R 1. 296NM 0. 566NM O:01 O:01 *1 Appears when the "RING" of the FUNCTION menu is turned ON. *3 Appears when the "WPT" of the FUNCTION menu is turned ON. To display the waypoint marker, bearing data and NMEA data with 0183 format is necessary. *4 This area may differ depending on DATA DISP selection in the FUNCTION menu. Nautical miles (NM) and kilometres (KM) can be selected in the INT. SETTING menu as the distance unit. [. . . ] r Push [TX (SAVE)] to cancel the power save function. · The save indicator turns OFF. EBL/VRM1 EBL/VRM2 S0672°R S0162°R 1. 296NM 0. 566NM O:01 O:01 EBL/VRM1 EBL/VRM2 S0672°R S0162°R 1. 296NM 0. 566NM O:01 O:01 Scan and standby alternates. NOTE: When you use the power save function together with the alarm function, the LCD display is turned OFF until an object enters the programmed alarm zone, therefore, more power saving is possible. 00) 14 BASIC OPERATION 4 s Ship speed indication When the ship speed data with NMEA 0183 format is applied, the radar can display the ship speed. Knots (KT) or kilometres/hour (KM/h) are automatically selected in the normal screen (p. w Push [DOWN] until "DIST UNIT" section becomes highlighted. r Push [MENU] to exit the menu display. s Long pulse function To magnify the blips for easier viewing of small targets, the long pulse and echo stretch (p. When the long pulse is used in the 3/4 to 2 NM range, this function magnifies target echoes to the backward direction of the target. 6) w Push [ ]/[ ] until the "PULSE" section becomes highlighted. 6). s Position indication When latitude/longitude data with NMEA 0183 format is applied, the radar can display the latitude and longitude of your ship's or cursor position in the bottom of the display. (To display the "CURSOR" position, bearing data is necessary. ) (P. e Push [ ]/[ ] to select SHIP (ship position) or CURS (cursor position). r Push [MENU] several times to exit the menu. s Bearing setting The radar bearing interface accepts NMEA, N+1 or AUX data format and the bearing can be used as a magnetic or true north type. When a true north type bearing is used, the variation from magnetic north, etc. , can be adjusted on 0. 1° steps. · Setting the bearing type q Push [MENU] twice to call up "EPA" menu. r Push [ ]/[ ] to select magnetic or true north type. · All displayed bearing readouts show the selected bearing type. s Waypoint indication When waypoint data received from navigation equipment with NMEA 0183 format is applied, the radar can display the waypoint. w Push [ ] until the "DATA DISP" section becomes highlighted. r Push [MENU] twice to exit the menu display. · Setting the magnetic variation q Push [ ] until the "MAG VAR" section becomes highlighted. w Push [ ]/[ ] to select an "AUTO*" or "MANU. " variation. e When a "MANU. " variation is selected, push [DOWN], then push [ ]/[ ] to set the bearing variation. r Push [MENU] to exit the menu display or push [ ] once to proceed to the bearing input setting. *NOTE: NMEA data is required for auto variation. 38) 15 5 DISTANCE AND DIRECTION MEASUREMENTS s Distance measurement Two measurement procedures are available with this radar. The distance unit, nautical miles (NM) or kilometres (KM) is selected in the "INIT. SETTING" menu (p. Displays a variable range marker. Suitable for accurate measurements from your own ship to a target. VRM1 VRM2 When the VRM1 and EBL1 selects a target, the center of VRM2 appears at the intersection point. [. . . ] (see left) i Push [MENU] to return to the normal screen. · DO NOT change the screen range before returning to the normal screen. 8 NM ENGLISH 24000 SPD ADJ. HV MONITOR HEATER MG TX TIME 4 6 36 8 12 16 24 30. 2 349 47 0. 53 0. 0 1. 2H 32 36 NOTE: When returning to the normal screen, the tuning level indicator automatically adjusts to 85% of the full scale. s Auto gain adjustment NOTE: While pushing and holding [MOB] and [TRAILS], push [POWER] to activate the `Auto gain' setting. e Push [ ]/[ ] to adjust the gain to the point where noise just begins to appear on the screen. · Beep tone "Pi pi" emits. 34 ERROR MESSAGE s Error message list Message BRG INPUT FAIL*1 TRIG SIGNAL FAIL*1 SHM SIGNAL FAIL*2 VIDEO SIGNAL FAIL*2 POSN INPUT FAIL*1 NO. [. . . ]