User manual ICOM ID-1

[. . . ] INSTRUCTION MANUAL DIGITAL TRANSCEIVER ID-1 DIGITAL TRANSCEIVER ID-1 MIC TD/RD PWR TX/RX POWER FOREWORD Thank you for purchasing this Icom product. The ID-1 DIGITAL is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. TRANSCEIVER IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. We want to take a couple of moments of your time to thank you for making your ID-1 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your ID-1. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the ID-1. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!WORD D FEATURES Current FM, Digital Voice and Data modes available Standard PC control application via USB terminal connection Remote controller for current mobile transceiver style operation (optional for some versions) Standard 10BASE-T connector for data transmission/reception i Icom, Icom Inc. [. . . ] · If the repeater indicator, "RP­" or "RP+, " and " " blink, confirm that the duplex direction and the offset frequency (p. 60) is set correctly. wSet the desired receive frequency (repeater output frequency). eClick [RP] several times to select minus or plus duplex. · "RP­" or "RP+" appears. Refer to page 60 for offset frequency setting. r Click [TONE] to turn the repeater tone encoder ON. · "TONE" appears. Refer to page 59 for tone frequency setting. NOTE for the USA version: During the auto repeater function ON, the steps e and r are not necessary, depending on the settings. See page 106 for the auto repeater function. Displays transmit frequency. uClick [MONI] to check whether the other station's transmit signal can be received directly. iTo return to simplex operation, click [RP] several times to clear the "RP­" or "RP+" indicator. oTo turn OFF the repeater tone encoder, click [TONE] several times until no tone indicators appear. Appear Click 57 REPEATER OPERATION-- VOICE 8 D Setting from the RC-24 q Push [MODE] to select FM mode. · "FM" appears. t Push and hold [PTT] to transmit. · The display frequency automatically changes to the transmit frequency (repeater input frequency). · If the repeater indicator, "RP-" or "RP+" blinks, confirm that the offset frequency (p. 60) is set correctly. wSet the desired receive frequency (repeater output frequency). e Push [RP·4] several times to select minus or plus duplex. · "RP-" or "RP+" appears. Refer to page 60 for offset frequency setting. y Release [PTT] to receive. During receive rPush [TONE· ·5] to turn the repeater tone encoder ON. LOW · "TONE" appears. Refer to page 59 for tone frequency setting. 1294. 500 FM RP- TONE During transmit 00 LOW NOTE for the USA version: During the auto repeater function ON, the steps e and r are not necessary, depending on the settings. See page 106 for the auto repeater function. [TONE· ·5] [RP·4] 8 1282. 500 FM RP- TONE 00 [MODE] LOW 1294. 500 FM RP- TONE 00 uPush and hold [SQL] to check whether the other station's transmit signal can be received directly. iTo return to simplex operation, push [RP·4] several times to clear the "RP-" or "RP+" indicator. oTo turn OFF the repeater tone encoder, push [TONE· ·5] several times until no tone indicators appear. 58 8 REPEATER OPERATION-- VOICE I Repeater tone frequency setting D Setting from the application qDisplays set mode screen by performing one of the following operations. wDouble click "Repeater Tone" frequency cell, then select the desired frequency from the displayed list. · To close the screen, click " " or repeat the operation as step q. Double click D Setting from the RC-24 q Push [MODE] several times to select FM mode. ePush [MODE] or [TXinh· ] to select "Repeater Tone" item. r Rotate [DIAL] to select the desired tone frequency. · See the table below for the available frequencies. t Push [PWR] momentarily to exit set mode. [DIAL] [TXinh· ] [MODE] LOW Appears 88. 5 Repeater Tone · Available tone frequencies (unit: Hz) 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 203. 5 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 Select from the above list. 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 59 REPEATER OPERATION-- VOICE 8 I Offset frequency setting D Setting from the application qDisplays set mode screen by performing one of the following operations. wDouble click "Offset Freq" frequency cell, then enter the desired frequency within 0 to 60. 000 MHz range. · To close the screen, click " " or repeat the operation as step q. [. . . ] · When setting the squelch from the RC-24, a level greater than `19' activates the squelch attenuator. · The S/RF meter shows the set level with the reversed indication. I AFC function The AFC (Automatic Frequency Control) function tunes the displayed frequency automatically when an off-set frequency is received. Click [AFC] in the application (main screen); or push [AFC· ·0] on the RC-24 to turn the AFC function ON and OFF. · "AFC" appears when the function ON. Appears Shows the set level. Click NOTE: The squelch attenuator functions even when the monitor function is in use. Thus set the [SQL] within 10 to 12 o'clock position (12 to 19 level when setting with the RC-24) is recommended when using the monitor function. [AFC· ·0] NOTE: The AFC function may not tune the signal properly when a weak signal is received and/or strong nearby signals are received. 111 OTHER FUNCTIONS 14 I CPU reset The function display may occasionally display erroneous information (e. g. [. . . ]