User manual ICOM IC-W31E SERVICE MANUAL

[. . . ] i EXPLICIT DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii 1 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer is activated, causing the transceiver to stop transmitting. · Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. w While pushing and holding [PTT], speak into the microphone at a normal voice level. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. 13 3 BASIC OPERATION D TX code number edit (PMR or BIIS PMR operation only) If the transceiver has [TX Code CH Select] or [TX Code Enter] assigned to it, TX code contents can be edited within the allowable digits. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select] to enter the TX code channel selection mode. · Select the desired channel before entering the TX code channel selection mode if necessary. D TX code channel selection If the transceiver has [TX Code CH Select] assigned to it, the indication can be toggled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, [CH Up] or [CH Down] selects the TX code channel. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select]-- a TX code channel number (or name) appears. e Push [Call] (or [PTT] during MSK operation) to transmit the selected TX code. r Push [TX Code CH Select] again to return to the operating channel number indication. USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY: If the transceiver has a [TX Code CH Up] or [TX Code CH Down] key assignment, the programmed TX code channel can be selected directly when pushed. NOTE for PMR or BIIS PMR operation: · The LCD indication does not change when the operating channel number (or name) is displayed. After pushing [Digital Button] or [TX Code CH Select], selects call list or TX code channel, respectively. w Push and hold [PTT], then speak into the microphone at a normal voice level. · TX indicator lights red. e Release [PTT] to return to receive. · BUSY indicator lights green while receiving a signal. r To finish the conversation, push [Moni(Audi)] to send the `Clear down' signal. · Either station can send a `Clear down' signal. · " " disappears and the transceiver returns to the standby condition. 17 4 BIIS OPERATION D Displaying the received call record -- Queue indication The transceiver memorizes the calling station ID in the memory. Up to 3 calls can be memorized, and the oldest call record is erased when a 4th call is received. However, once the transceiver is powered OFF, the all records are cleared. q Push and hold [Digital Button] for 1 sec. · Displays following indication. D Group call q When a group call is received; · Beeps sound. G · The programmed text message (e. g. "GROUP") and the calling station ID (or text) is displayed when the indication mode is 2 lines. G · The programmed text message (e. g. "GROUP") and the calling station ID (or text) is displayed alternately when the indication mode is 1 line, depending on the setting. Appears Appears or blinks When a record is available GROUP 1120 CALL BIFN TXC TXCE ­QUEUE!­ CALL BIFN TXC TXCE <QUEUE> w Push and hold [PTT], then speak into the microphone at a normal voice level. · TX indicator lights red. When no record is available NOTE: Only one station is permitted to speak. e Release [PTT] to return to receive. · BUSY indicator lights green while receiving a signal. <QUEUE> NO QUEUE CALL BIFN TXC TXCE r To finish the conversation, push [Moni(Audi)] to send the `Clear down' signal. · Either station can send a `Clear down' signal. (approx. ) · " " disappears and the transceiver returns to the standby condition. w Push [CH Up] or [CH Down] to select the desired call. again to return to the standby condition. · When no operation is performed for 30 sec. , the transceiver returns to the standby condition automatically. 18 BIIS OPERATION 4 Transmitting a call A total of 3 ways for code selection are available--selecting the call code from memory, entering the call code from the keypad and calling back from the queue channel record. D Calling back from the queue channel q While in the standby condition, push and hold [Digital Button] for 1 sec. [. . . ] 1 w Base clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2)) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a `click' sound. r Once the transceiver is locked in place, it swivels as illustrated below. Once the transceiver is locked in place, it will swivel 360 degrees. 34 SWIVEL BELT CLIP 7 Detaching q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. 2)) e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w 7 CAUTION! HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged. 35 8 BP-231 BP-232 BP-240 OPTIONS D BELT CLIPS Capacity 1150 mAh 2000 mAh Battery life * 8 hrs. [. . . ]