User manual ICOM IC-V8000

[. . . ] INSTRUCTION MANUAL VHF FM TRANSCEIVER iV8000 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom product. The IC-V8000 VHF FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. MR/CALL MW [Y]/[Z] z Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. [EXAMPLE]: Transferring memory channel 30 contents to VFO. Front panel operation: Push M/CALL to select memory mode. Push MW S. MW for 1 sec. HM-133V operation: Push to select memory mode. Select memory channel. Push then push for 1 sec. 27 MEMORY OPERATION D Memory/callcall/memory q Select the memory/call channel to be transferred. Push [M/CALL(PRIO)] to select memory mode, then rotate the tuning dial to select the desired memory channel. w Push [MW(S. MW)] momentarily. · "M" indicator and "­ ­" indication blink, and shows VFO conditions. 5 MR/CALL MW [Y]/[Z] z Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. x Push [FUNC], then [CLR A(MW)] momentarily. · "M" indicator and "­ ­" indication blink, and shows VFO conditions. 5 e Rotate the tuning dial to select the target memory channel. · "C" blinks when the call channel is selected. · Scan edge channels, 1A/1b, 2A/2b, 3A/3b, can also be selected. r Push [MW(S. MW)] for 1 sec. to transfer the selected memory/call channel contents to the target memory. · The targeted memory and transferred contents are indicated. c Push [Y]/[Z] to select the target memory channel. · "C" blinks when the call channel is selected. · The keypad cannot be used for the selection. v Push [FUNC] then push [CLR A(MW)] for 1 sec. to transfer the selected memory/call channel contents to the target memory. · The targeted memory and transferred contents are indicated. [EXAMPLE]: Transferring memory channel 30 contents to channel 31. Front panel operation: Select the memory channel, then push MW S. MW . Select the target channel. Push MW S. MW for 1 sec. HM-133V operation: Select the memory channel, push then push . Push then push for 1 sec. 28 5 MEMORY OPERATION I Memory clearing Contents of programmed memories can be cleared (blanked), if desired. w Push [MW(S. MW)] momentarily. · "M" indicator and the memory channel number blink. r Push [MW(S. MW)] momentarily, then push [MW(S. MW)] again for 1 sec.  This operation must be performed within 1. 5 sec. · When clearing the call channel, the current VFO conditions are re-programmed into the call channel automatically. e Rotate the tuning dial to select the memory channel to be cleared. · Memory channels not yet programmed are blank. t Push any switch, except [MW(S. MW)], to return to VFO mode. NOTE: Be careful!-- the contents of cleared memories CANNOT be recalled. [EXAMPLE]: Clearing memory channel 20. Push V/MHz SCAN to select VFO. Push MW S. MW momentarily. Rotate for selecting memory channel. Push MW S. MW momentarily, then push MW S. MW again for 1 sec. " " "Beep Push any switch, except Beep " Beep " MW S. MW . 29 MEMORY OPERATION 5 I Programming channel names Each memory channel and the call channel can be programmed with an alphanumeric channel name for easy recognition and can be indicated independently by channel. Names can be a maximum of 6 characters-- see the table below for available characters. (space) (1) (B) (L) (V) (+) (2) (C) (M) (W) (­) (3) (D) (N) (X) (=) (4) (E) (O) (Y) () (5) (F) (P) (Z) (/) (6) (G) (Q) (() (7) (H) (R) ()) (8) (I) (S) (|) (9) (J) (T) (0) (A) (K) (U) r Push [SET(LOCK)] to select the channel name programming condition. · Frequency readouts disappear. t Rotate the tuning dial to select the desired character. · The selected character blinks. y Push [SET(LOCK)] or [MW(S. MW)] to move the cursor to left or right, respectively. i Push [V/MHz(SCAN)] to program the name and exit the channel name programming condition. to return to frequency indication if desired. 5 q Push [M/CALL(PRIO)] to select memory mode. to select channel name indication mode. · 1 short and 1 long beep sound. IMPORTANT!: Once channel name indication mode is selected, always access the channel name programming condition when [SET(LOCK)] is pushed. When set mode accessing is necessary, cancel the channel name indication by pushing [MONI(ANM)] for 1 sec. , then access to set mode. SET Push LOCK or the cursor. MW S. MW [EXAMPLE]: Programming "CLUB" into memory channel 1. Select memory channel 1, then push MONI for 1 sec. Push V/MHz SCAN . 30 5 MEMORY OPERATION Channel names can also be programmed via the microphone. z Select the memory/call channel to be assigned memory names. [. . . ] In such a case, both transceivers automatically return to the clone standby condition and cloning must be repeated. 12 Microsoft and Windows are registered trademarks of Microsoft Corporation in the U. S. A. and other countries. 70 13 MAINTENANCE If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. · Blown fuse. I Troubleshooting PROBLEM No power comes on. SOLUTION REF. -- · Check the connector pins. · A selective call or squelch function is activated such as pocket beep or tone squelch. Sensitivity is low and only · Antenna feedline or the antenna connector solder · Check, and if necessary, replace the feedline or sol- p. [. . . ]