Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
VHF TRANSCEIVER
iV82 iV82-T
UHF TRANSCEIVER
iU82
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC-V82
IC-U82
FOREWORD
Thank you for purchasing this Icom product. The IC-V82/U82 VHF/UHF TRANSCEIVERS are designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] intervals) is the slowest.
PWR
PRIO
7
SET
8
H/M/L
9
ENT
ENT
rPush [·ENT
] to exit INITIAL SET MODE.
29
8
Band edge
SCAN OPERATION
Programmed scan
End 1b 2b 3b
Scan types
PROGRAMMED SCAN
Start 1A 2A 3A Scan edges Scan Jump Programmed scan P1 scans between 1A and 1b, P2 scans between 2A and 2b, and P3 scans between 3A and 3b frequencies.
Band edge
Programmed scan repeatedly scans between two user programmed frequencies (memory channels "1A3A" and "1b3b") or scans between upper and lower band edges. This scan is useful for checking for signals within a specific frequency range such as repeater output frequencies, etc. wPush [A·FUNC] and [5·SCAN] to start the scan, then a selected scan edge appears as "P1, " "P2, " "P3" or "AL. "
· To change the scan edge, push [A·FUNC] and [8·SET] several times until the desired scan edge appears. · "AL" for full scan, "P1", "P2" and "P3" for programmed scan between the programmed scan edge channels as "1A""1b, " "2A""2b" and "3A""3b. " Y Z · To change the scan direction, push [Y] or [Z]. · When [VOL] is assigned as tuning dial, rotate [VOL] to change the scan direction. 14, 65) Push
A FUNC
MEMORY (SKIP) SCAN
Mch 1 Mch 0 Mch 199 Mch 10 Mch 2 Mch 3 Mch 4 Mch 5
SKIP
Mch 9 Mch 8
SKIP
Mch 7
Mch 6
PRIORITY WATCH
Priority memory channel watch
VFO frequency 145. 20 MHz 5 sec.
Mch 3
Priority channel
SCAN
5
50 msec.
Mch 3
Priority memory channel scan
Mch 2
e Push [D·CLR] to stop the scan.
Mch 4 Mch 5
VFO frequency 145. 20 MHz 5 sec.
Memory scan Priority channels
Mch 1
50 msec.
Mch 199
Mch 6
SKIP
30
SCAN OPERATION
8
Memory scan
NOTE: Scan edges, 1A3A/1b3b, must be programmed in advance. 22) If identical frequencies are programmed into the scan edges, programmed scan will not proceed. Memory scan repeatedly scans all programmed memory channels, except those set as skip channels. q Push [C·MR] to select memory mode, if necessary.
· "X" appears. · See below to select bank scan.
w Push [A·FUNC] and [5·SCAN] to start the scan.
Y Z · To change the scan direction, push [Y] or [Z]. · When [VOL] is assigned as tuning dial, rotate [VOL] to change the scan direction. 14, 65) Push
MONI PWR A FUNC B CALL C MR D CLR
8
A FUNC
SCAN
5
TONE
1
P. BEEP
2
T. SCAN
3
BANK
e Push [D·CLR] to stop the scan.
DUP
4
SCAN
5
SKIP
6
OPT
0
PRIO
7
SET
8
H/M/L
9
ENT
· Bank scan --Select the desired bank in step q above. q Push [A·FUNC] and [#·BANK] to select memory bank mode.
w Rotate [VOL] to select the desired bank, A to J. e Push [·ENT ] (or [D·CLR]) to select the bank.
31
8
SCAN OPERATION
Skip channels
In order to speed up the scan rate, you can select memory channels you don't wish to scan as skip channels. q Push [C·MR] to select memory mode, if necessary.
· "X" appears.
Priority watch
Priority watch checks for signals on "priority channels" while operating on a VFO frequency.
D Memory or call channel watch
While operating on a VFO frequency, memory or call channel watch monitors for signals in the selected memory or call channel every 5 sec. e Push [A·FUNC], then push [7·PRIO] to start watching.
w Select a memory channel to set as a skip channel. ePush [A·FUNC] and [6·SKIP] to toggle the skip setting ON and OFF.
· "SKIP" appears when the channel is set as a skip channel. Push
A FUNC
SKIP
6
"SKIP" appears
· VFO is displayed, then the decimal point ". ", on the frequency readout blinks. · When the signal is detected on the priority channel, the watching is suspended according to the setting of the scan resume condition.
VFO frequency Memory channel
5 sec.
50 msec.
r Push [D·CLR] to stop watching.
32
SCAN OPERATION D Memory scan watch
While operating on a VFO frequency, memory scan watch monitors for signals in each memory channel in sequence, every 5 sec. q Push [C·MR] to select memory mode, if necessary.
· "X" appears.
8
Scan resume condition
USING
SET MODE
wPush [A·FUNC], then push [5·SCAN] to start the memory scan. e Push [A·FUNC], then push [7·PRIO] to start the watching.
· VFO is displayed, then the decimal point ". ", on the frequency readout blinks. · When the signal is detected on the priority channel, the watching is suspended according to the setting of the scan resume condition.
VFO frequency
Mch 3 Mch 2 Mch 1
When a signal is received during scanning, the scan resume condition determines what action the transceiver takes. [. . . ] · HM-128L EARPHONE-MICROPHONE You can clip the microphone with PTT switch to your lapel or breast pocket. Includes VOX, PTT and "one-touch" PTT with time-out timer.
15 16
77
16
OPTIONS
· VS-1L PTT/VOX UNIT+HS-94/HS-95/HS-97 HEADSET VS-1L PTT/VOX UNIT Required when using these headsets. HS-94 EAR-PIECE TYPE HEADSET Earhook headset with flexible boom microphone. HS-95 NECK-ARM TYPE HEADSET Behind-the-head headset with flexible boom microphone. [. . . ]