User manual ICOM IC-R3

[. . . ] INSTRUCTION MANUAL COMMUNICATIONS RECEIVER iR3 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the receiver. CAUTIONS R WARNING!NEVER operate the receiver with a headset or other audio accessories at high volume levels. If you experience a ringing in your ears, reduce the volume level or discontinue use. [. . . ] In this case, the frequencies will not be skipped even if skip information is programmed and "P SKIP" or "P" does not appear. w Push [FUNC] + [(V/M) SKIP] to toggle the frequency skip function ON or OFF. · "PSKIP" or "P" appears when the function is turned ON. FM 146. 010. 000 TS 15. 0 I Frequency skip function D Programming a skip frequency Unwanted frequencies can be skipped and programmed as skip channels when full scan, band scan or programmed scan is pausing. 19) w While receiving an unwanted signal and scan pauses, push [FUNC] + [(V/M) SKIP] for 2 sec. to program the received frequency as a skip frequency. · The receiver emits 3 beeps and the scan resumes. · Non-programmed memory channels (blank channels) are used for skip frequency programming in reverse sequence. · To scan the skip frequency after programming, cancel the skip information (p. 16). FM PSKIP 2P 370. 475. 000 TS 15. 0 FM PSKIP 146. 010. 000 TS 15. 0 S1 VOL 3 5 7 9 S1 VOL 3 5 7 9 FM FM FM PSKIP H49 370. 475. 000 P TS 15. 0 The frequency skip function is OFF. The frequency skip function is ON. S1 RX VOL 3 5 7 9 S1 RX VOL 3 5 7 9 FM FM RX P RX P Indication while pausing Indication while programming 24 PRIORITY WATCH I Priority watch types Priority watch checks for signals on a frequency every 5 sec. In addition, you can be alerted with beeps and a flashing " ". 125 msec. VFO frequency Memory channel 7 While operating on a VFO frequency, priority watch checks for a signal on the selected memory channel every 5 sec. · A memory channel with skip information can be watched. The watch resumes according to the selected scan resume condition. If the pocket beep function is activated, the receiver automatically selects the tone squelch function when priority watch starts. MEMORY SCAN WATCH (p. 26) 5 sec. VFO frequency SKIP 125 msec. Mch 00 Mch 01 Mch 02 Mch 49 While operating on a VFO frequency, priority watch checks for signals on each memory channel in sequence. · The memory skip function and/or memory bank scan is useful to speed up the scan. VFO SCAN WATCH (p. 27) While scanning in VFO mode, priority watch checks for signals on the selected 5 sec. VFO Memory scanning channel 25 7 PRIORITY WATCH r Rotate [DIAL] to select "Priority" or "PRIo. " · "PRIo" disappears after 1 sec. and "oFF" and "PR" appears when color LCD is OFF. I Priority watch operation D Memory channel watch and memory scan watch q Select VFO mode; then, set an operating frequency. e Push [FUNC] + [(MODE) SET] momentarily to enter set mode. · Select a non-band scope screen in advance for color LCD. t Push [] or rotate the tuning dial while pushing [FUNC] to select priority watch ON or priority watch ON with alert (BELL). · If the pocket beep function is activated, the receiver automatically selects the tone squelch function when the priority watch is selected. y Push [(MODE) SET] to exit set mode and start the watch. · The receiver checks the memory channel frequency every 5 sec. · The watch resumes according to the selected scan resume condition. 22) · If the priority watch with alert is ON, you can be alerted with beeps and a flashing "P. B" or " ". · If the direction finding screen is selected, the receiver automatically selects the simple screen when the priority watch starts. FM M:A18 145. 765. 000 TS PRIO 15. 0 Pause Scan Priority Beep Audio Light A. Power OFF : 10SEC : OFF : VOLUME : AUTO : OFF Pause Scan Priority Beep Audio Light A. Power OFF : 10SEC : ON : VOLUME : AUTO : OFF Pause Scan Priority Beep Audio Light A. Power OFF : : : : : 10SEC BELL VOLUME AUTO OFF FM 9 RX PRIO S1 RX VOL 3 5 7 While pausing on the memory channel, "PRIO" flashes. Priority watch with alert is ON. u Push [V/M] while the display shows the VFO frequency to stop the watch. 26 PRIORITY WATCH D VFO scan watch q Select the desired memory channel to be watched. 19) r Push [FUNC] + [(MODE) SET] momentarily to enter set mode. · Select a non-band scope screen in advance for color LCD. 7 u Push [(MODE) SET] to exit set mode and start the watch. · The receiver checks the memory channel frequency every 5 sec. · The watch resumes according to the selected scan resume condition. 22) · If the priority watch with alert is ON, you can be alerted with beeps and a flashing "P. B" or " ". [. . . ] 12 · Some set mode items can be selected only when the color LCD is ON. · Some set mode items cannot be selected in the broadcast band. · Turn the color LCD ON. 38 56 QUICK REFERENCE q Cut w Fold e Complete 19 Important operating instructions are summed up in this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc. iR3 I BASIC OPERATION q Push [POWER] for 2 sec. t Rotate [DIAL] to change the frequency. · The frequency changes according to the preset tuning steps. y Set the squelch level. · While pushing [SQL], rotate [DIAL]. [. . . ]