User manual ICOM IC-R2500
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ICOM IC-R2500. We hope that this ICOM IC-R2500 user guide will be useful to you.
You may also download the following manuals related to this product:
ICOM IC-R2500 BROCHURE (321 ko)
ICOM IC-R2500 BROCHURE (583 ko)
Manual abstract: user guide ICOM IC-R2500
Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
iR2500
COMMUNICATION RECEIVER
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FOREWORD
Thank you for purchasing this Icom receiver. The IC-R2500 COMMUNICATIONS RECEIVER is designed and built with Icom's state of the art technology and craftsmanship. With proper care, this receiver should provide you with years of troublefree operation. [. . . ] y Repeat steps q to t for transferring or erasing an another bank's contents.
After [SET·SKIP] released
32
6
SCAN OPERATION
Scan types
Scanning searches for signals automatically and makes it easier to locate new stations. There are 5 scan types and 4 resume conditions to suit your operating needs.
FULL SCAN (p. 34)
10 kHz Scan Jump 3299. 9999 MHz
Repeatedly scans all frequencies over the entire band. Some frequency ranges are not scanned according to the frequency coverage of the receiver's version. Skip channels can be turned ON and OFF by pushing and holding [SET·SKIP] in memory mode.
PROGRAMMED SCAN
(p. 34)
Band edge Scan edges xxA Scan Jump Band xxB edge
Repeatedly scans between two user-programmed frequencies. Used for checking for frequencies within a specified range such as repeater output frequencies, etc.
MEMORY (SKIP) SCAN
(p. 34)
SKIP
A00 A99 A98 A05 A04 A01 A02 A03
Repeatedly scans all bank channels or selected bank channels. Skip scan is also available.
SKIP
SKIP
FREQUENCY/MEMORY SKIP FUNCTION (p. 36)
Band edge Scan SKIP Jump SKIP Band edge
Skips unwanted frequencies or channels that inconveniently stop scanning. This function can be turned ON and OFF by pushing and holding [SET·SKIP] in memory mode.
33
SCAN OPERATION
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Scan start/stop
D Preparation
Scan resume condition (p. IMPORTANT!: To perform memory or bank scan, two or more memory/bank channels MUST be programmed, otherwise the scan will not start. r Push [SET·SKIP] (or [ATT·PRIO]) to select full and programmed scan (P00 to P49), if VFO is selected in step q. About the scanning steps: The selected tuning step in each frequency band (in VFO mode) is used during scan. · During memory scan · During bank scan
D Operation
qPush [VFO/MR·S. MW] once or twice to select VFO mode for full/programmed scan; or to select memory mode for memory/bank scan.
· Select the desired bank in memory type selection mode for bank scan.
wSet the squelch level to the point where noise is just muted. to start the scan.
· To change the scanning direction, rotate the main band's [DIAL]. · The memory channel readout blinks the scan type as below.
· During full scan
· During programmed scan
Push [SET·SKIP] to select full (ALL) or programmed scan (P00P49) in sequence.
Indicates scan edge channels. · P01 stands for 01A/01B · P00 to P49 are available when they are programmed, and selected with [SET·SKIP].
Indicates bank channel. NOTE: When SSB, CW, AM, FM, WFM or Digital mode frequencies are programmed into memory channels randomly, memory scan is slow because changing modes takes time. In this case, assign the SSB, CW, AM, FM, WFM or Digital mode frequencies into separate banks where bank scan can be used. And using the bank scan is helpful.
While pushing and holding [MODE·SCAN], rotate [DIAL] also to select full (ALL) or programmed scan (P00P49).
34
6
SCAN OPERATION
Scan edges programming
Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edges, 0A/0B to 49A/49B, in memory channels. [. . . ] after inputting frequency ranges.
D Cloning using a personal computer
Data can be cloned to and from a personal computer (Microsoft® Windows® XP/2000/Me/98SE) and other settings can also be programmed from a PC. Consult the IC-PCR1500/ICPCR2500's Instruction manual for cloning details.
Main unit
Skip area settings
· The skip area setting is available for skipping unwanted frequency ranges that inconveniently stop scanning. PC to ground to AC adapter USB cable to USB port
Microsoft and Windows are registered trademarks of Microsoft Corporation in the U. S. A. and other countries.
66
11
OTHER FUNCTIONS
Partial reset
AT
POWER ON
All reset
AT
POWER ON
If you want to initialize the operating conditions (VFO frequency, VFO settings, set mode contents) without clearing the memory contents, a partial reset function is available. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-R2500
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-R2500 will begin.