User manual ICOM IC-P7A

[. . . ] INSTRUCTION MANUAL VHF/UHF DUAL BAND FM TRANSCEIVER iP7A This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-P7A VHF/UHF DUALBAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] qWhile pushing and holding [FUNC], push and hold [SQL] (ATT·SET) for 1 sec. to enter set mode. [DIAL] · OFF · DUP ONLY · DUP TONE · OFF · ON USA/KOREA versions only eWhile pushing and holding [FUNC], rotate [DIAL] to select the desired condition. (default) Korea version: r Push [SQL] (ATT·SET) to exit set mode. D Frequency range and offset direction · U. S. A. version: Frequency range SCAN Duplex direction "­" appears "+" appears "+" appears "­" appears S. MW 145. 200­145. 495 MHz 146. 610­146. 995 MHz 147. 000­147. 395 MHz 442. 000­444. 995 MHz DTCS ATT SET SET wRotate [DIAL] to select "AUTORP. " WFMAM -DUP T SQL DTCS ATT WFMAM -DUP T SQL 447. 000­449. 995 MHz · Korea version: Frequency range 439. 000­440. 000 MHz VOL PRIO P SKIP MR 9 5 LOW 1 After 1 sec. VOL PRIO P SKIP MR 9 5 LOW 1 Auto repeater item Setting indication Duplex direction "­" appears 23 MEMORY/CALL CHANNELS General description The IC-P7A has 1050 memory channels including 50 scan edge memory channels (25 pairs) for storage of often-used frequencies. And a total of 18 memory banks, A to H, J, L, N, O to R, T, U and Y are available for storing groups of frequencies, etc. Up to 100 channels can be assigned into a bank. 6 Memory channel programming q Push [V/M] (SKIP·S. MW) to select VFO mode. w Set the desired frequency: Select the desired band with [BAND] (TS·LOCK). offset frequency, duplex direction, subaudible tone frequency, etc. ), if desired. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. D Memory channel contents The following information can be programmed into memory channels: · Operating frequency (p. 14) · Duplex direction (DUP or ­DUP) with an offset frequency (pgs. 39). 5 6 r Rotate [DIAL] to select the desired channel. · Call channels (C0, C1), VFO (VF) and scan edge channels (00A/00b to 24A/24b), as well as regular memory channels, can be programmed in this way. · While pushing and holding [FUNC], rotate [DIAL] to select memory channel in 10 channel steps. t Push and hold [V/M] (SKIP·S. MW) for 1 sec. · 3 beeps sound · Memory channel number automatically increases when continuing to push [V/M] (SKIP·S. MW) after programming. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel). Push WFMAM -DUP T SQL S. MW for 1 sec. WFMAM -DUP T SQL Rotate DTCS ATT WFMAM -DUP T SQL Push DTCS ATT S. MW for 1 sec. WFMAM -DUP T SQL DTCS ATT DTCS ATT WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 24 6 MEMORY/CALL CHANNELS Memory bank setting The IC-P7A has a total of 18 banks (A to H, J, L, N, O to R, T, U and Y). Regular memory channels, 000 to 999, may assigned into a desired bank for easy memory management. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. rWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank. · Banks A to H, J, L, N, O to R, T, U and Y are available. · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. Bank is selected with WFMAM -DUP T SQL + w Rotate [DIAL] to select the desired memory channel. eWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "BANK. " · After releasing [CALL] (MODE·SCAN), "-- -- -- --" is displayed instead of the frequency indication, and only " " indicator blinks. · Bank group and channel number is displayed if the selected memory channel has already been assigned to a bank. · "BANK" can can also be selected by pushing [CALL] (MODE·SCAN) several times. [DIAL] WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 t Rotate [DIAL] to select the desired bank channel number. · Vacant bank channel numbers are only be displayed. [. . . ] NOTE: Connect the HM-153P after removing the [MIC/SP] cap (MIC/SP jack cover). Keep the [MIC/SP] cap attached when jack are not in use to keep the contact clean. OPC-782 Microphone Microphone HM-153 Speaker/MIC connector HM-153P 15 SCAN SCAN S. MW S. MW SET SET 78 15 OPTIONS D LC-161 CARRYING CASE Helps protect the transceiver from scratches, etc. NOTE: When using as below illustration, tension release loop protects the [MIC/SP] connector from being damaged by cable stress or vibration OPC-782 HM-128 D HM-128 EARPHONE MICROPHONE An optional OPC-782 is required for connection. q w Transceiver D HM-131 SPEAKER MICROPHONE An optional OPC-782 is required for connection. HM-131 LC-161 Tension release loop e 79 POCKET GUIDE Important operating instructions are summed up in this and the following page for your simple reference. [. . . ]