User manual ICOM IC-P2AT-ET

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NEVER allow children to touch the receiver. DO NOT use or place the receiver in areas with temperatures below 0°C (+32°F) or above +50°C (+122°F) or, in areas subject to direct sunlight. AVOID placing the receiver in excessively dusty environments. AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they damage the receiver surfaces. Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the U. S. A and other countries. [. . . ] The antenna connector type is BNC, so an adapter may be necessary to connect an optional antenna. 2 COMM ICATIO iC- pc NS RE r100 CEIVE R 0 UN INSTALLATION 1 I AF output level selection The received audio can be input into your computer via the sound card. Before inputting the received audio into the [LINE IN] connector (connector name depends on your sound card), the output level of the [EXT-SP] must be set properly. Perform as follows: q Remove the 8 screws from the cover as shown below. Open the cover. w Select the output level as shown below. - "SPEAKER" for internal speaker. - "PHONES" for PC sound card or headphones. e Replace the 8 screws and cover. r Connect an appropriate cable between IC-P2AT-ET and PC. - Plug for [EXT-SP] is supplied with the receiver. IC-P2AT-ET COMMUN ICAT iC- pc IONS RECEIVE r100 R 0 SPEAKER PHONES to [LINE IN] (depends on your sound card) [EXT-SP] 3 1 INSTALLATION I TNC connection The IC-P2AT-ET can receive 9600 bps packet communication (AFSK). Connect the TNC (Terminal Node Controller) as follows. to [PACKET] 4 COMM UNICAT IONS iC- pcr 1000RECEIVER IC-P2AT-ET TNC Personal computer INSTALLATION 1 I Software installation When installing into a Windows XP or Windows 2000 environment, log on as the administrator. r Type the setup program name with full path name, then push the [Enter] key. (D:\SETUP. exe [Enter]) t Click [OK]. * The following screens show Windows XP. · The "InstallShild® Wizard" starts preparing the installation. y After the preparation, the following dialog is displayed. Installing starts. Click Click 5 1 INSTALLATION I Uninstallation This section describes [IC-P2AT-ET] uninstallation. D Windows XP [Procedure] q Click <Start> and select [Control Panel]. w Click [Add or Remove Programs] and select [ICOM ICPCR1000] and click <Change/Remove>. Moving the knob to the right increases the speed; to the left decreases the speed. !9 VSC (Voice Scan Control) button Turns the voice scan control function on and off. This function detects whether signals are modulated (contain voice or music components, etc. ) or not. @0 SET button Shows/hides the [Setting] dialog box used to adjust settings for scan functions, the band scope function and the automatic mode function. @1 Condition indicator window Indicates the scan function operating condition. When a scan is paused, Pause appears in the Condition indicator window. @4 Center indicators Indicate the tuning level when selecting the 6 kHz or 15 kHz IF filter in FM mode. @5 BUSY indicator Appears when receiving a signal or when signal noise opens the squelch. Used to temporarily mute audio output. #8 T (Tone squelch) button Shows/hides the [TONE SQUELCH] dialog box for setting tone squelch tone frequencies. 10 PANEL DESCRIPTION 2 #9 $0 $1 $2 $3 #9 $4 $5 $6 $2 LIMIT indicator Indicates when the tuning step is greater than the automatic sweep step setting. In the diagram, the tuning step is greater than the automatic sweep step setting and the tuning step (TS) and the sweep step width are not the same. $3 Sweep step indicator Indicates band scope sweep step. $7 $4 STOP button Stops the band scope (sweep) function. [. . . ] : 0. 010000­823. 999999* 849. 000001­868. 999999 894. 000001­1300. 000000 Europe : 0. 010000­1300. 000000* * Specifications guaranteed 0. 5­1300 MHz only. · Receive system : Triple superheterodyne · Mode : WFM, FM, AM, SSB, CW · Frequency stability : ±3 ppm at 1300 MHz (0°C to +50°C; 32°F to +122°F) · Frequency resolution : 1 Hz (minimum) · Power supply requirement : 13. 8 V DC ±15 % for receiver unit; or, supplied AC adapter (negative ground) · Current drain (at 13. 8 V DC) Power ON (PC power OFF) : 0. 1 A Max. range : 0°C to +50°C; +32°F to +122°F · Intermediate frequencies 1st : 266. 7 MHz 2nd : 10. 7 MHz 3rd : 450 kHz (except WFM) · Receive sensitivity (typical)*: 3 WFM Frequency (MHz) 0. 5­1. 799999 1. 8­27. 99999 28­29. 99999 30­49. 99999 50­699. 99999 700­1300 SSB/CW 0. 56 µV 0. 28 µV 0. 35 µV 0. 2 µV 0. 25 µV AM 2. 5 µV 1. 4 µV 1. 8 µV 1. 0 µV 1. 3 µV FM (10 dB S/N) (10 dB S/N) (12 dB SINAD) (12 dB SINAD) -- -- 0. 5 µV 0. 32 µV 0. 4 µV 0. 79 µV 1. 0 µV * When 230 kHz (for WFM), 15 kHz (for FM), 6 kHz (for AM) and 2. 8 kHz (for SSB/CW) passband widths are selected. · Squelch sensitivity (threshold): Frequency (MHz) 0. 5­1. 799999 1. 8­27. 99999 28­29. 99999 30­49. 99999 50­699. 99999 700­1300 SSB/CW 14 µV AM 1. 8 µV FM -- WFM 7. 1 µV 0. 89 µV -- 0. 63 µV 0. 5 µV 0. 63 µV 5. 6 µV 7. 1 µV 5. 6 µV 7. 1 µV 0. 71 µV 0. 89 µV 13 3 SPECIFICATIONS · Selectivity WFM WFM/FM/AM FM/AM FM/AM/SSB/CW AM/SSB/CW · IF shift range · Max. [. . . ]