User manual ICOM IC-M710

[. . . ] WORD D FEATURES Simple operation with large keys Easy to hear speaker Built-in DSC meets ITU Class D requirement Rugged waterproof construction Optional COMMANDMIC IIITM (HM-162E) is available Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. COMMANDMIC III is a trademark of Icom Incorporated (Japan) in the United States. CLEAN THE TRANSCEIVER AND MICROPHONE THOROUGHLY WITH FRESH WATER after exposure to water including salt, otherwise, the keys and switch may become inoperable due to salt crystallization. i IN CASE OF EMERGENCY If your vessel requires assistance, contact other vessels and the Coast Guard by sending a Distress call on Channel 16. INSTALLATION NOTE The installation of this equipment should be made in such a manner as to respect the EC recommended electromagnetic field exposure limits (1999/519/EC). The antenna should be installed as high as possible for maximum efficiency and that this installation height should be at least 5 meters above ground (or accessible) level. [. . . ] · To transmit on the selected channel during Dualwatch/Triwatch, push and hold [PTT]. Tri-watch resumes after the signal disappears. INT DUP TAG TRI 16 34°34. 506N 34 34. 506N 123°23. 236W 123 23. 236W UTC 12:00 TELEPHONE 12:00 25W Signal received on Channel 16 takes priority. BUSY 25W INT DUP TAG TRI 16 34°34. 506N 34 34. 506N 123°23. 236W 123 23. 236W UTC 12:00 TELEPHONE 12:00 14 DSC OPERATION I MMSI code programming The 9-digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be programmed at power ON. w While pushing [MENU], turn power ON to enter MMSI code programming condition. S t Rotate [CHANNEL] to select "Set up , " push [CHANNEL·ENTER]. --DSC Menu-Select Item Position Input Received Calls Set up Set Exit 6 u Rotate [CHANNEL] to set the specific 9-digit MMSI code. · Push [16·C] or [DIAL·DUAL/GRP] to move the cursor forward or backward, respectively. · Push [CLR] to cancel and return to the set up menu. --DSC Menu-MMSI Check _________ 5 6 <CLRExit <CLR Exit / ENT OK> ENTOK> i After entering the 9-digit code, push [CHANNEL·ENTER] to set the code. · Returns to the set up menu. E o Push [CLR] or rotate [CHANNEL] to select "Exit, " push [CHANNEL·ENTER]. · Returns to the DSC menu. · Repeat again to return to the normal operation condition. M y Rotate [CHANNEL] to select "MMSI Check , " push [CHANNEL·ENTER]. --DSC Menu-Set up Add:INDV ID Add:Group ID DEL:INDV ID DEL:Group ID Offset Time MMSI Check MMSI 15 6 DSC OPERATION I MMSI code check The 9-digit MMSI (DSC self ID) code can be checked. S w Rotate [CHANNEL] to select "Set up , " push [CHANNEL·ENTER]. --DSC Menu-Select Item Position Report Polling Request Received Calls Distress Setting Set up Exit r Check the 9-digit MMSI (DSC self ID) code. --DSC Menu-MMSI Check 123456789 <CLRExit> E t Push [CLR] or rotate [CHANNEL] to select "Exit, " push [CHANNEL·ENTER]. · Returns to the DSC menu. · Repeat again to return to the normal operation condition. M e Rotate [CHANNEL] to select "MMSI Check , " push [CHANNEL·ENTER]. --DSC Menu-Set up DEL:Group ID Offset Time MMSI Check Auto ACK NMEA Output Exit 16 DSC OPERATION 6 I DSC address ID A total of 100 DSC address IDs can be programmed and named with up to 10 characters. r Rotate [CHANNEL] to set the individual ID and ID name. · Push [16·C] or [DIAL·DUAL/GRP] to move the cursor forward or backward, respectively. F · "Full ID" appears when 100 DSC address IDs are already set. · After inputting the 9-digit MMSI number, push [CHANNEL· ENTER] or [16·C] to enter a 10-character ID name. --DSC Menu-Add:Individual ID Input 9 digits _________ Input name _________ <CLRExit / ENTOK> D Programming Individual ID q Push [MENU] to enter the DSC menu. S w Rotate [CHANNEL] to select "Set up , " push [CHANNEL·ENTER]. --DSC Menu-Select Item Position Report Polling Request Received Calls Distress Setting Set up Exit 6 A e Rotate [CHANNEL] to select "Add:INDV ID , " push [CHANNEL·ENTER]. --DSC Menu-Set up Add:INDV ID Add:Group ID DEL:INDV ID DEL:Group ID Offset Time MMSI Check t After inputting, push [CHANNEL·ENTER] to program. · Rotate [CHANNEL] to edit N; North latitude or S; South latitude when the cursor is on the `N' or `S' position, and W; West longitude or E; East longitude when the cursor is on the `W' or `E' position. · Push [CLR] to cancel and return to the DSC menu. <CLR 1sec Null Data> 1secNull <CLRExit <CLR Exit / ENT OK> ENTOK> E t Push [CLR] or rotate [CHANNEL] to select "Exit, " push [CHANNEL·ENTER]. · Returns to the DSC menu. · Repeat again to return to the normal operation condition. Manually programmed position data will be held for 23. 5 hours only. 21 6 DSC OPERATION I Position and time indication When a GPS receiver (NMEA0183 ver. 2. 0 or 3. 01) is connected, the transceiver displays the current position and time. When no GPS receiver is connected, the transceiver displays the manually entered position and time. Ask your dealer about suitable GPS receivers. 25W TAG INT I GPS information indication When a GPS receiver (NMEA0183 ver. 2. 0 or 3. 01) is connected, the transceiver displays the GPS information after pushing and holding [CHANNEL·ENTER] for 1 sec. --GPS Info-- Push for 1 sec. : JAN/16/2006 : 12:00 : 34°34. 506N 123°23. 236W COURSE: 261°M SPEED : 18. 5kt DATE UTC POS 34°34. 506N 123°23. 236W UTC 12:00 CALLING When connecting GPS receiver is compatible with several sentence formatters, the order of input precedence is `RMC, ' `GGA, ' `GNS', `GLL' and `VTG. ' When the connecting GPS receiver is compatible with several sentence formatters, the order of input precedence is `RMC, ' `GGA, ' `GNS' and `GLL. ' When sentence formatter `RMC' is received, time indication includes a date. "??" may blink instead of position and time indications when the GPS data is invalid, or has not been manually updated after 4 hours. 22 DSC OPERATION 6 I Distress call A distress call should be transmitted, if in the opinion of the Master, the ship or a person is in distress and requires immediate assistance. e After transmitting the distress call, the transceiver waits for an acknowledgment call on Channel 70. · The distress call is automatically transmitted every 3. 5 to 4. 5 minutes. [. . . ] The optional HM-162E should be installed to the transceiver using the supplied connection cable. The connector of the connection cable can be installed into a cabinet, wall, etc. , as a built-in plug. For longer distance remote operation, the optional extension cable, OPC-1541 (6 m; connecting between transceiver and the connection cable), is available, and up to two OPC-1541 can be added. 9 63 9 CONNECTIONS AND MAINTENANCE y The completed installation should look like this. q Insert the supplied cable into the external microphone jack and tighten the cable nut as shown below. w To use the supplied cable as a wall socket, perform the following steps. e Using the mounting base as a template, carefully mark the holes where the cable and three screws will be fastened. [. . . ]