User manual ICOM IC-M125

[. . . ] Wait for an acknowledgment from a coast station. · Channel 16 is automatically selected. 3. Push and hold [PTT], then transmit the appropriate information as at left. Versions of the IC-M125 which display the "CE" symbol on the serial number seal, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. ò This warning symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use. Be sure to check that you have the correct version of this radio or the correct programming of this radio, to comply with national licensing requirement. [. . . ] 7) 2 PANEL DESCRIPTION 2 I Function display !0 q w e r t y u y ATIS INDICATOR "ATIS" appears when the ATIS encoder is activated. · The ATIS encoder is available for Germany and Holland versions only. u DUPLEX INDICATOR (p. " " appears during dualwatch; " " appears during triwatch. 7) Indicates whether an International (I) or U. S. A (U) channel is selected. · USA channel group is available for U. K. 8) "BUSY" appears when receiving a signal or when the squelch opens. r CALL CHANNEL INDICATOR "CALL" appears when the call channel is selected. 8) "LOW" appears when low power is selected. !0 CHANNEL NUMBER READOUT Indicates the selected operating channel number. · "A" appears when a simplex channel is selected. 15) 3 2 PANEL DESCRIPTION e CHANNEL 16/CALL CHANNEL SWITCH [16/C] Same as the [16] switch on the front panel. 6) · "CALL" appears when call channel is selected. I Microphone q Microphone w e Push for 3 sec. to enter call channel programming condition when call channel is selected. 9) · Microphone lock function q PTT SWITCH [PTT] Push and hold to transmit; release to receive. 8) YZ w CHANNEL UP/DOWN SWITCHES [Y]/[Z] Push either switch to change the operating memory channel, set mode contents, etc. Clear the tag channels which inconveniently stop scanning, such as channels used for digital communication. 15) PRIORITY SCAN CH 01 CH 02 NORMAL SCAN CH 01 CH 02 CH 06 CH 16 CH 03 CH 06 CH 03 CH 05 CH 04 CH 05 CH 04 Priority scan searches through all tag channels in sequence while monitoring Channel 16. When a signal is detected on Channel 16, scan pauses until the signal disappears; when a signal is detected on a channel other than Channel 16, scan becomes dualwatch until the signal disappears. 12 Normal scan, like priority scan, searches through all tag channels in sequence. However, unlike priority scan, Channel 16 is not checked unless Channel 16 is set as a tag channel. SCAN OPERATION 5 I Setting tag channels For more efficient scanning, add desired channels as tag channels or clear tag channels for unwanted channels. q While pushing [H/L], push [CH] one or more times, select the desired channel group, if desired. channel group is available for UK and Italy versions only. ) w Select the desired channel to set as a tag channel. e Push [TAG] to set the displayed channel as a tag channel. · "TAG" appears in the function display. I Starting a scan Set scan type (priority or normal scan) and scan resume timer in advance using set mode. w While pushing [H/L], push [CH] one or more times, select the desired channel group, if desired. channel group is available for UK and Italy versions only. ) e Push [SCN] to start priority or normal scan. · "SC 16" or "SCAN" appears in the function display. · When a signal is detected, scan pauses until the signal disappears or resumes after pausing 5 sec. , according to set mode setting. [. . . ] 2 u Mounting screws (5 × 20 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 i Flat washers (M5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 o Spring washers (M5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 *Depending on version. I Fuse replacement Two fuses are installed in the supplied DC power cable. [. . . ]