User manual ICOM IC-F6022

[. . . ] INSTRUCTION MANUAL VHF MOBILE TRANSCEIVER UHF MOBILE TRANSCEIVER iF5022 iF6022 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before usng the transcever. EXPLICIT DEFINITIONS WORD RWARNING CAUTION NOTE DEFINITION Personal njury, fre hazard or electrc shock may occur. No rsk of personal njury, fire or electrc shock. SAVE THIS INSTRUCTION MANUAL -- Ths nstructon manual contans mportant operatng nstructons for the IC-F5022 VHF MOBILE TRANSCEIVER and the IC-F6022 UHF MOBILE TRANSCEIVER. Icom, Icom Inc. and the Icom logo are regstered trademarks of Icom Incorporated (Japan) n Japan, the Unted States, the Unted Kngdom, Germany, France, Span, Russa and/or other countres. All other products or brands are regstered trademarks or trademarks of ther respectve holders. PRECAUTIONS RWARNING! [. . . ] Ask your dealer whch call s assgned to each key. SURVEILLANCE KEY Push to turn the survellance functon ON or OFF. When ths functon s turned ON, the beep s not emtted and the LCD backlght does not lght when a sgnal s receved or a key s pushed, etc. TX CODE ENTER KEY (PMR operaton only) Push to enter the TX code edt mode drectly. Therefore "01234" and "56789" are the same. 2 1. 1. 2 1. 3 1. 4 1. 5 1. 6 Channel selection Several types of channel selectons are avalable. NON-ZONE TYPE: Push [CH Up] or [CH Down] to select the desred operatng channel, n sequence; or, push one of [MR-CH 1] to [MR-CH 4] keys to select a channel drectly. ZONE TYPE: Push [Zone], then push [CH Up] or [CH Down] to select the desred zone. Scannng stops when recevng a call. KEY NUMBER 0 5 1 6 2 7 3 8 4 9 e When the "PASSWORD" ndcaton does not clear after nputtng 4 dgts, the nput code number may be ncorrect. Turn the power off and start over n ths case. 7 2 BASIC OPERATION Call procedure When your system employs tone sgnalng (excludng CTCSS and DTCS), a call procedure may be necessary pror to voce transmsson. The tone sgnallng employed may be a selectve callng system whch allows you to call specfic staton(s) only and prevents unwanted statons from contactng you. q Select the desred TX code channel, 2/5-tone code accordng to your System Operator's nstructons. · Ths may not be necessary dependng on programmng. · Refer to pages 9­10 for selecton. Receiving and transmitting Receiving: q Push and hold [ ] for 1 sec. e When recevng a call, rotate [VOL] to adjust the audo output level to a comfortable lstenng level. NOTE: Dependng on the pre-settng, the transcever automatcally transmts the mcrophone audo for the specfied tme perod* when a matched RX code sgnal s receved. · HM-148G or HM-152 hand microphone s requred. Ask your dealer for detals. w Push [Call] (assgned to one of the dealer programmable keys). e After transmttng, the remander of your communcaton can be carred out n the normal fashon. Selective calling Non-selective calling Transmitting: Wat for the channel to become clear to avod nterference. q Take the mcrophone off hook. · The `audble' condton s selected. · A prorty channel may be selected automatcally. w Wat for the channel to become clear. · The channel s busy when BUSY ndcator appears on the LCD. e Whle pushng and holdng [PTT], speak nto the mcrophone at your normal voce level. Hold the mcrophone 5 to 10 cm (2 to 4 nches) from your mouth, then speak nto the mcrophone at a normal voce level. 8 BASIC OPERATION D Transmitting notes D TX code channel selection 2 1. 1. 2 1. 3 1. 4 1. 5 1. 6 · Transmit inhibit function The transcever has several nhbt functons whch restrct transmsson under the followng condtons: - The channel s n mute condton (`Inaudble' condton; " " (Audble ndcator) does not appear. ) - The channel s busy. - Un-matched (or matched) CTCSS s receved. (Dependng on the pre-settng) If the transcever has [TX Code CH Select] assgned to t, the ndcaton can be toggled between the operatng channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) s dsplayed, [CH Up] or [CH Down] selects the TX code channel. [. . . ] to stop the beep and dsplay ndcaton. 13 3 CONNECTION AND MAINTENANCE Rear panel connection Antenna q ANTENNA CONNECTOR Connects to an antenna. e MICRO. HONE HANGER Connect the suppled mcrophone hanger to the vehcle's ground for mcrophone on/off hook functons. Red Black t r r O. TIONAL CABLE (O. C-1. 939) Connect an external modem, dmmer control, etc. Ths could damage the transcever. 1. 2V Battery 14 NOTE: Use the termnals as shown below for the cable connectons. [. . . ]