User manual ICOM IC-F4160DT

[. . . ] OPERATING GUIDE OPERATING GUIDE FOR IC-F3162DT/DS IC-F4160DT/DS BIIS 1200/dPMR OPERATION IMPORTANT Thank you for purchasing this Icom transceiver. The Binary Interchange of Information and Signaling (BIIS) 1200 and digital Private Mobile Radio (dPMR) system functions are built into your IC-F3162DT/DS or IC-F4162DT/DS transceiver. NOTE: In this operating guide, the LCD illustration is shown as having characters displayed in two lines. READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS OPERATING GUIDE -- This guide contains important operating instructions for: · IC-F3162DT/DS vhf dpmr mobile transceiver · IC-F4162DT/DS uhf dpmr mobile transceiver i Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. [. . . ] When the function is activated, the transceiver automatically transmits position data according to the `Time Marker' and `Interval Timer' settings. - Set the `Auto' item to "Enable. " 11 NOTE: Configure the position data transmission settings using the CS-F3160/F5060 (dPMR) cloning software. Ask your dealer for details. BIIS 1200 OPERATION 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Printer connection When a printer is connected to the transceiver, through the OPC-966 interface cable, received SDM and the calling station's ID can be printed out, depending on the pre-programmed settings. Ask your dealer or system operator for connection and setting details. 12 3 dPMR OPERATION Receiving a call D Receiving an Individual call q When an Individual call is received: · Rings sound. · " " appears or blinks, depending on the pre-programmed settings. Appears Appears or blinks dPMR operation The IC-F3162DT/IC-F3162DS and IC-F4162DT/IC-F4162DS provide digital Private Mobile Radio (dPMR) operation that meets the 6. 25 kHz bandwidth requirements for narrow band operation. This increases the efficiency of channel allocation and use of the spectrum. NOTE: During dPMR operation, BIIS 1200 operation is disabled. dPMR display The following displays appear in dPMR operation. CONNECT : When an acknowledgement of a Voice or Emergency call is received. OK : When an acknowledgement of a message (status message or SDM) or command (Ambience Listening, Stun, Kill, or Revive) is received. : When no name is programmed, appears to the left of the calling station's ID. : When no name is programmed, appears to the left of the Talkgroup ID. Calling station's ID dPMR CALL TXCE CLR ID 0000001 FAILED WAIT ID TG 13 w While holding down [PTT], speak into the microphone at your normal voice level. r After the communication is finished, push [Clear] to send a `Disconnect' signal to terminate the connection. · Either station can send a `Disconnect' signal. · " " disappears, "CLR DOWN" appears for approximately 2 seconds, and the transceiver automatically returns to the stand-by mode. CLR DOWN : When a connection is terminated. dPMR OPERATION D Receiving a Group call q When a Group call is received: · Rings sound. · " " appears or blinks, depending on the pre-programmed settings. · The Talkgroup ID (or name) and the calling station's ID (or name) blink. · When an All Call is received, "ALL CALL" blinks instead of "TG" and the Talkgroup ID. Appears Appears or blinks 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D Receiving a status message q When a status message is received: · Rings sound. · The calling station's ID (or name) and the status message blink. The received status message Calling station's ID dPMR CALL TXCE CLR RX Status 00 ID 0000001 w Push [Clear] to return to the stand-by mode. Talkgroup ID Calling station's ID dPMR CALL TXCE CLR TG ID 0100000 0000001 w While holding down [PTT], speak into the microphone at your normal voice level. r After the communication is finished, push [Clear] to send a `Disconnect' signal to terminate the connection. · Either station can send a `Disconnect' signal. · " " disappears, "CLR DOWN" appears for approximately 2 seconds, and the transceiver automatically returns to the stand-by mode. 14 3 dPMR OPERATION Receiving a call (continued) D Receiving an SDM q When an SDM is received: · Rings sound. · The calling station's ID (or name) and the SDM are displayed. D Receiving a Stun, Kill or Revive call If an Individual call with a Stun or Kill command is received from a specified station, the transceiver will display "SORRY, " and becomes unusable. [. . . ] Ask your dealer for details. D Transmitting a Stun Call A Stun call allows you to send a command that will stun the target station. q Push [dPMR Button] to enter the ID selection mode. · The pre-programmed ID is displayed. D Transmitting an Ambience Listening Call An Ambience Listening call allows you to send a command that will require the target station to transmit its microphone audio. q Push [dPMR Button] to enter the ID selection mode. · The pre-programmed ID is displayed. w Push [CH Up] or [CH Down] to select a desired Individual ID. e Push [dPMR Button] again to enter the application selection mode. · "STATUS" is displayed. w Push [CH Up] or [CH Down] to select a desired Individual ID. [. . . ]