User manual ICOM IC-F4029SDR

[. . . ] INSTRUCTION MANUAL UHF TRANSCEIVER iF4029SDR IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. PRECAUTIONS R CAUTION!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-F4029SDR UHF TRANSCEIVER. R CAUTION!NEVER operate the transceiver with a headset or other audio accessories at high volume levels. R CAUTION! [. . . ] This allows you to confirm whether or not a call has reached to the member of your group even if the operator is temporarily away from the transceiver. q Set the same operating channel and CTCSS tone code for all of your group transceivers. w Push (S-Ring/Ringer) to send the Smart-Ring call. · " " and " " appears. · When a member of your group station answers your call, the transceiver emits beep tones for every 10 sec. · Push [Side1] (MONI) to cancel the Ringer beep and " " blinks. · When no answer comes back, the transceiver emits short failure beep tones. While transmitting Communication Piro Piro 5 4 5 Push (S-Ring/Ringer) Answer back (automatic) Piro P iro Appears Appears e Push [PTT] to answer the call and to stop the beeps and blinking. NOTE: This function is available only when the called station has use the same CTCSS tone code and the same operating channels as you. 14 5 RINGER FUNCTION (Analog mode operation only) I Call-Ring operation q Set the same operating channel and CTCSS tone code for all of your group transceivers. w Push and hold (S-Ring/Ringer) to send the pre-selected ring tone to your group members. ·" " and " " appears. · The ring tone* is emitted while (S-Ring/Ringer) is pushed and held. · The same ring tone comes from your group station's speaker. While transmitting I Auto channel function The auto channel function automatically searches a clear channel during scan when (S-Ring/Ringer) is pushed. Then, the ringer tone is transmitted for a specified period in the founded clear channel. Another station during scanning may answer the call in the clear channel if it receives the ringer signal. q Push [Auto Ch] to start scan. · The selected scan type and scan list are available. to transmit a ringer tone. (S-Ring/Ringer) for 1 Appears Appears · The auto channel function automatically searches a clear channel. · To call a waiting station by voice, push [PTT] until beep tones sound (for longer than the ringer time), then speak into the microphone. * The Call-Ring emission type can be selected in Set mode. later after a busy signal disappears and in which no operation is performed while the auto channel function is in use. r Push [Auto Ch] to cancel the function. 15 TONE SQUELCH OPERATION (Analog mode operation only) ` Operation By default, the transceiver uses a CTCSS/DTCS squelch system. You can silently wait for calls from group members using the same tone. 6 y When the received signal includes a matching tone, squelch opens and the signal can be heard. · When the received signal's tone does not match, tone squelch does not open. · To open the squelch temporarily, push [Side1] (MONI). D CTCSS tone setting The transceiver is equipped with 50 CTCSS tones. [. . . ] 280 g : Double conversion superheterodyne · Sensitivity (20 dB SINAD) : 26. 5 dBµV/m · Squelch sensitivity : 26. 5 dBµV/m · Intermodulation rejection ratio : 86. 29 dBµV/m · Spurious response rejection ratio : 91. 29 dBµV/m · Adjacent channel selectivity : 81. 29 dBµV/m · Audio output power : 0. 5 W (typical) at 5% distortion with a 8 load 0. 6 W (typical) at 5% distortion with a 6 load · External speaker connector : 2-conductor 3. 5 (d) mm/8 · Receive system · Frequency coverage Analog Digital · Mode · Current drain (at 7. 2 V) · Power supply requirement · Frequency stability · Antenna impedance · Dimensions · Weight All stated specifications are subject to change without notice or obligation. D Transmitter · Output power · Modulation system · Max. frequency deviation · Spurious emissions · Adjacent channel power · External mic. connector : 0. 5 W : Variable reactance frequency modulation : ±2. 5 kHz : 0. 25 µW or below 1 GHz 1. 00 µW above 1 GHz : 60 dB : 3-conductor 2. 5 (d) mm/2. 2 k 37 SPECIFICATIONS 12 I Channel frequency lists Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Zone 1 (Analog mode) Frequency (MHz)*1 Tone (Hz)*2 446. 006250 446. 018750 446. 031250 446. 043750 446. 056250 446. 068750 446. 081250 446. 093750 446. 006250 446. 018750 446. 031250 446. 043750 446. 056250 446. 068750 446. 081250 No setting No setting No setting 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 Zone 2 (Analog mode) Frequency (MHz)*1 446. 006250 446. 093750 446. 031250 446. 068750 446. 043750 446. 018750 446. 081250 446. 056250 446. 006250 446. 093750 446. 031250 446. 068750 446. 043750 446. 018750 446. 056250 446. 081250 Tone (Hz)*2 94. 8 88. 5 103. 5 79. 7 118. 8 123. 0 127. 3 85. 4 107. 2 110. 9 114. 8 82. 5 132N 155N 134N 243N 12 *1 All operating channel frequencies are fixed. 17) 38 12 SPECIFICATIONS I Channel frequency lists (Continued) Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Zone 3 (Analog mode) Frequency (MHz)*1 446. 006250 446. 018750 446. 031250 446. 043750 446. 056250 446. 068750 446. 081250 446. 093750 Tone (Hz)*2 67. 0 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 Zone 4 (Digital mode) Frequency (MHz)*1 446. 103125 446. 109375 446. 115625 446. 121875 446. 128125 446. 134375 446. 140625 446. 146875 446. 153125 446. 159375 446. 165625 446. 171875 446. 178125 446. 184375 446. 190625 446. 196875 Common ID*3 85 87 93 95 117 119 125 127 213 215 221 223 245 247 253 254 *1 All operating channel frequencies are fixed. [. . . ]