User manual ICOM IC-F3162T

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iF3162T/S iF3162DT/DS UHF TRANSCEIVER iF4162T/S iF4162DT/DS The photo shows the 10-key version UHF transceiver. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. instruction manual contains important operating instructions for the IC-F3162T, IC-F3162S, IC-F3162DT and IC-F3162DS VHF TRANSCEIVERS and IC-F4162T, IC-F4162S, ICF4162DT and IC-F4162DS UHF TRANSCEIVERS. See the operating guide for details of BIIS, MDC, LTR ® and Digital system operations. Ask your dealer for details. EXPLICIT DEFENITIONS WORD RDANGER RWARNING CAUTION NOTE DEFINITION Personal death, serious injury or an explosion may occur. [. . . ] · Refer to pages 14 or 15 for selection. Receiving and transmitting NOTE: Transmitting without an antenna may damage the transceiver. w Push [CH Up] or [CH Down], or rotate [ROTARY SELECTOR]* to select the conventional system channel, in sequence. *Depending on the pre-setting. w Push [Call] (assigned to one of the dealer programmable keys) e After transmitting, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling e When receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level. · When a tone signalling system is used, the call procedure described at the previous page may be necessary. w Release [PTT] to return to receive. Hold the microphone 5 to 10 cm from your mouth, then speak into the microphone at a normal voice level. 13 BASIC OPERATION 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D Transmitting notes · Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition (`Inaudible' condition; " " (Audible indicator) does not appear. ) - The channel is busy. - Un-matched (or matched) CTCSS is received. (Depending on the pre-setting. ) D TX code channel selection If the transceiver has [TX Code CH Select] assigned to it, the indication can be toggled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, [CH Up] or [CH Down] selects the TX code channel. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select]-- a TX code channel number (or name) appears. e After selecting, push [TX Code CH Select] to set. · Return to the stand-by mode. - The selected channel is a `receive only' channel. · Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer starts, causing the transceiver to stop transmitting. · Penalty timer Once the time-out timer starts, transmission is further inhibited for a period determined by the penalty timer. r Push [Call] to transmit the selected TX code. USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY: If the transceiver has a [TX Code CH Up] or [TX Code CH Down] key assignment, the programmed TX code channel can be selected directly when pushed. 14 3 BASIC OPERATION D TX code number edit (PMR operation only) If the transceiver has [TX Code CH Select] or [TX Code Enter] assigned to it, TX code contents can be edited within the allowable digits. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select] to enter the TX code channel selection mode. · Select the desired operating channel before entering the TX code channel selection mode if necessary. USING [TX CODE ENTER] KEY: q After pushing [TX Code CH Select], push [CH Up] or [CH Down], or push [TX Code CH Up] or [TX Code CH Down] to select the desired TX code channel. w Push [TX Code Enter] to enter the TX code edit mode. · The digit to be edited blinks. w Push [TX Code CH Select] for 1 sec. to enter the TX code edit mode. · The digit to be edited blinks. e Push [TX Code CH Select] to select the desired digit to be edited. u After editing, push [TX Code CH Select] to set. · Return to the stand-by mode. e Push [TX Code Enter] to select the desired digit to be edited. u After editing, push [TX Code Enter] to set. · Return to the stand-by mode. i Push [Call] to transmit. D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. e Push [DTMF Autodial] to transmit the DTMF code. i Push [Call] to transmit. 15 BASIC OPERATION 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. You can "customize" the transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [P1] and [P2], rotate [VOL] to turn the power ON. · Turn power OFF in advance. · "SET MODE" appears for 1 sec at power ON. Emergency transmission When [Emergency] is pushed for the specified time period, an emergency signal is automatically transmitted. 9) When [Emergency] is pushed for the specified time period, the DTMF or 5-tone* emergency signal is transmitted once or repeatedly on the emergency channel. [. . . ] · UT-126H digital modulator/demodulator unit Provides 6. 25 kHz digital mode operation. · UT-124R man down unit Provides a measure of safety when working in a hazardous environment, etc. OPTIONS D DC CABLES D ANTENNAS 8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 · CP-17L cigarette lighter cable Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N) · OPC-515L/OPC-656 dc power cables Allows charging of the battery pack using a 13. 8 V power source instead of the AC adapter. OPC-515L : For BC-119N OPC-656 : For BC-121N D OTHER OPTIONS · SP-13 earphone Provides clear receive audio in noisy environment. [. . . ]