User manual ICOM IC-F310 IC-F320 IC-F410 IC-F420

[. . . ] i CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1­5 s Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 s Function display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · When the optional UT-105 is installed, push one or more times to select a channel bank for conventional channels or SmarTrunk IITM channels. SCAN START/STOP KEY Push this key to start scanning; and push again to stop. Push and hold this key to indicate the scan group, then push to select the desired group. TAG s Programmable function keys The following functions can be assigned to [P0], [P1], [P2], [P3], [ ] and [ ] programmable function keys. Consult your Icom Dealer or System operator for details concerning your transceivers programming. In the following explanations, programmable function names are bracketed, the specifc switch used to activate the function depends on programming. CH UP CH DN PRI A PRI B BANK SCAN CH UP AND DOWN KEYS · Select an operating channel. · Select a transmit code channel after pushing the [TX CH] key. · Select a scan group after pushing and holding the [SCAN] key. CH 1 CH 2 CH 3 CH 4 OPERATING CHANNEL KEYS Select an operating channel directly. SCAN TAG KEY Adds or deletes the selected channel to the scan group. BEEP Push to turn the beep tones ON/OFF. BEEP 3 PANEL DESCRIPTION LOCK KEY Electronically locks all programmable keys except the following: · [CALL] (incl. MONITOR KEY Activates one of (or two of) the following functions on each channel independently: · Push and hold the key to unmute the channel (audio is emitted; `Audible' condition). · Push the key to toggle the mute and unmute conditions (toggles `Audible' and `Inaudible'). · Push the key to mute the channel (sets to `Inaudible' only). · Push the key to unmute the channel (sets to `Audible' only). · Push the key after the communication is finished to send a `reset code'. 1 LOCK HIGH LOW1 OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily or permanently depending on the pre-setting. level for each selection. LOW2 · Ask your Dealer or System Operator for the output power MONI TA TALK AROUND KEY Turns the talk around function ON and OFF. · The talk around function equalizes the transmit frequency to the receive frequency for mobile-to-mobile communication. CALL CAL A CAL B CALL KEYS Transmit a 5-tone call. · Call transmission is necessary before you call another station depending on your signaling system. · The [CAL A] and/or [CAL B] keys may be available when your system employs selective `Individual/Group' calls. Ask your System Operator which call is assigned to each key. NOTE: The unmute condition (`Audible' condition) may automatically return to the mute condition (`Inaudible` condition) after a specified period. WIDE/NARROW KEY Push [W/N] to toggle bandwidth between wide or narrow. · This function is available for W/N versions only. EMER EMERGENCY KEY Push and hold the key to transmit an emergency call. · If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. · The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. W/N 4 1 PANEL DESCRIPTION TX CODE KEY Select a transmit 5-tone code (station code) channel. · Push and hold to changes the contents of the station code using [ ]/[ ] keys. · Push to selects a TX 5-tone code channel using [ ]/[ ] keys after pushing this key. TX CODE CHANNEL UP/DOWN KEY Push to selects a TX code channel directory. · Push this key, then select the desired DTMF channel using the [ ]/[ ] keys. [. . . ] w Enter the memory location (0­9, A, B, C, D), the telephone or subscriber number, then [1], [M] (or [3], [M] if for another system subscriber). · A high-pitched beep indicates successful programming. · Memories [A]­[D] are used for the Turbo SpeeDial. D Last number redial Push [M], [M] to automatically redial the last number called. · A high-pitched beep indicates that the number is accepted. D System busy indication If all channels are busy, three low beeps sound after you initiate a call. Try the call again later. D Memory speed-dialing To automatically dial a commonly used number from memory: · Push [M] followed by the memory location (0­9). D PTT dispatch operation q Push [PTT] once (without dialing) to initiate a dispatch call. w Begin talking after you hear three beeps (one short, highpitched, two very-short, low-pitched). [. . . ]