User manual ICOM IC-F3062T-S

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iF3062T/S iF4062T/S UHF TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. WORD SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-F3062T/S VHF TRANSCEIVERS and IC-F4062T/S UHF TRANSCEIVERS. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i TABLE OF CONTENTS IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] NOTE for PMR or BIIS PMR operation: · The LCD indication does not change when the operating channel number (or name) is displayed. (Depending on the pre-setting) · To check the selected TX code, push [TX Code CH Select]. w Push and hold [TX Code CH Select] for 1 sec. e Push [TX Code CH Select] to select the desired digit to be edited. · The digit to be edited blinks. r Push [CH Up], [CH Down] or 10-keypad* to set the desired digit. The digit to the right will blink automatically. · When the 10-keypad* is used for setting, the digit to the right will blink automatically without pushing [TX Code CH Select]. y Repeat r and t to input all allowable digits. u Push [Call] or [PTT] to transmit the edited TX code. *IC-F3062T/IC-F4062T (10-key type) only 14 BASIC OPERATION USING [TX CODE ENTER] KEY: q Select the desired TX code channel via [TX Code CH Select]+[CH Up] or [CH Down], [TX Code CH Up] or [TX Code CH Down]. e Push [TX Code Enter] to select the desired digit to be edited. · The digit to be edited blinks. 3 D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. e Push [DTMF Autodial] to transmit the DTMF code in the selected DTMF channel. 3 r Push [CH Up], [CH Down] or 10-keypad* to set the desired digit. The digit to the right will blink automatically. · When the 10-keypad* is used for setting, the digit to the right will blink automatically without pushing [TX Code CH Enter]. y Repeat r and t to input all allowable digits. u Push [Call] or [PTT] to transmit the edited TX code. *IC-F3062T/IC-F4062T (10-key type) only 15 3 BASIC OPERATION User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can "customize" the transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [P1] and [P2], rotate [VOL] to turn the power ON. Then push [Side2] or [Side3] to set the desired level/condition. · Available set mode functions are Backlight, LCD contrast, Beep, Beep Level, Ringer Level, SQL Level, AF Min Level, Mic Gain, VOX Gain, VOX Delay, Battery Voltage and Signal Moni. Scrambler function The voice scrambler function provides private communication between stations. The frequency inversion type is equipped to all versions, moreover, the optional Rolling or Non-rolling type can be available. q Push [Scrambler] to turn the scrambler function ON. · " " appears. w Push [Scrambler] again to turn the scrambler function OFF. · " " disappears. e Rotate [VOL] to turn the power OFF to exit user set mode. 10)) [User Set Mode] section. 16 BIIS OPERATION Setting example The following functions are assigned to each programmable key for display example. [P0]; Call : Push to transmit a 5-tone/BIIS call when the selected channel is a 5-tone or BIIS channel. C · "CALL" is displayed on the key indicator. 4 3 4 Receiving a call D Individual call q When an individual call is received; · Beeps sound. C · The programmed text message (e. g. "CALLING") and the calling station ID (or text) is displayed when the indication mode is 2 lines. C · The programmed text message (e. g. "CALLING") and the calling station ID (or text) is displayed alternately when the indication mode is 1 line, depending on the setting. Appears Appears or blinks [P1]; Digital Button : Push to select the call list ID/transmit message, or to display the receive message record for selection. B · "BIFN" is displayed on the key indicator. B When this key is pushed, "BIFN " is inverted as " . " [P2]; Null : No function is assigned. [P3]; TX Code Enter : Push to enter the ID code edit mode directly for both 5-tone and BIIS. T · "TXCE" is displayed on the key indicator. CALLING 0500 CALL BIFN TXC TXCE [Emer]; Null [Side1]; Moni(Audi) : No function is assigned. : Push this key after the communication to send a `Clear down' signal during BIIS channel operation. [. . . ] ­ *2 1 D BATTERY PACK Battery pack Voltage 7. 4 V 7. 4 V · MB-93 SWIVEL BELT CLIP · MB-94 BELT CLIP Exclusive alligator-type belt clip. · MB-96N/96F LEATHER BELT HANGER Battery case for AAA (LR03) × 6 alkaline * 1 Operating periods are calculated under the following conditions; TX : RX : standby = 5 : 5 : 90 * 2 Operating periods depends on the alkaline cells used. D OPTIONAL UNITS · UT-96R 2/5 TONE UNIT · UT-109R /UT-110R SCRAMBLER UNITS Non-rolling type (UT-109R)/Rolling type (UT-110R) voice scrambler unit provides higher communication security. D CHARGERS ·BC-119N DESKTOP CHARGER + AD-106 CHARGER ADAPTER + BC-145 AC ADAPTER For rapid charging of battery packs. ·BC-121N MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs. ) + BC-157 AC ADAPTER For rapid charging of up to 6 battery packs (six AD-106's are required) simultaneously. ·BC-160 DESKTOP CHARGER + BC-145 AC ADAPTER For rapid charging of battery packs. [. . . ]